Sheet Metal Machines (In Stock at Facility) - Sheet Metal Machines

TIN KNOCKER TK24 24 ga. Pittsburgh Roll Former w/Stand and Flanger Attachment

lt2@sierravictor.com — Thu, 28 Sep 2023 16:11:33 +0000

On the job site or in the shop, this portable little rollformer is a work horse for 24 gauge and lighter material. It is available with power flanging attachment and is perfect for field use. Steel stand included.
Portable rollformer is a work horse for 24 gauge and lighter material.
It is available with power flanging attachment and is perfect for field use.
With the included, all steel stand, it will also fit right in with your other shop equipment.
NOTE: When shipping, rollformer will fit inside stand

SPECIFICATIONS:
Capacity: 24 Gauge Mild Steel
Motor: 1/2 HP, 1700 RPM, 115 Volt, Single Phase, 60 Hz – Standard (optional – 230v/1/50 available – please call)
Depth of Pocket: Approx. 5/16″ (7.9mm) with hammer edge of 3/8″ (9.53mm)
Speed: Approx. 35 FPM
Flange Height: 3/16″ (4.76mm)
Dimensions of Roll Former: 30″ x 14″ x 20″ (762mm x 356mm x 508mm)
Dimensions of Stand: 35″ x 14″ x 24″ (889mm x 483mm x 610mm) add 6″ around for shipping
Shipping Dimensions: 41″ x 25″ x 30″ (1,041mm x 65mm x 762mm)
Weight: Rollformer: 305 lbs

OPTIONAL MODEL:
TIN KNOCKER TK24 24 ga. Pittsburgh Roll Former w/Stand = $2,950.00

Specifications are subject to change without notice.
NOTE: Data is provided by the manufacturer.
WARRANTY: 1 YEAR – Parts

The post TIN KNOCKER TK24 24 ga. Pittsburgh Roll Former w/Stand and Flanger Attachment appeared first on Sheet Metal Machines.

TIN KNOCKER 16 ga. Gang Slitter

smm-admin — Tue, 23 May 2023 19:46:36 +0000

Cut multiple blanks of light gauge sheet metal… in one pass!
Great for roofing and architectural!
Gang slit blanks from 16 to 30 gauge.
Slit blanks at speeds up to 60 FPM
Gang slit pre-painted and other sheet material
Life lubed bearings
3” cold rolled polish shafts
2 sets of reversible knives
Heavy duty chain drive
Stripper fingers to prevent twist
Operating Speed: 60 FPM
3/4 HP, 110/220V, 1 Phase Motor
Tool steel blades with stripper rings
(Non-scratch: pre-painted, copper, polished metals, etc.)

SPECIFICATIONS:
Overall width: 58
Width between end frames: 52-1/4″
Max Cutting Width: 48-1/2″
Table Height: 35″
Feed Speed: 60 FPM
Overall depth: 26″
Shaft Diameter: 3″
Knife Dimensions: 5” OD x 1/4”
Motor HP: 3/4 HP
Electrics: 110/220V – 1ph
Ship Dimensions: 67” x 37” x 48”
Weight: 525 lbs.

Specifications are subject to change without notice.
NOTE: Data is provided by the manufacturer.
WARRANTY: 1 YEAR – Parts

The post TIN KNOCKER 16 ga. Gang Slitter appeared first on Sheet Metal Machines.

AKYAPAK APK 81 3 x 3 x 3/8 in. Angle Bending Roll – Options Available

smm-admin — Tue, 23 May 2023 23:45:00 +0000

Our machines are strong and reliable with their St-52 weld construction body. Minimum flexion causes less deformation, by the help of our machines’ enlarged roll diameters. By the help of big measurements of bearings, durability and high bending momentum can be obtained. Hydraulic cylinders’ power enables to bend the bigger parts without any difficulty. Practical and universal rollers create the possibility of easiness about bending various kinds of profiles, and this feature gives the opportunity of being more powerful and firm.
Our Profile Bending Machines are 3 Rolls driven. This feature allows having the possibility of making, the high capaticied bending processes, real. Secondly, our 3 Rolls Driven machine minimizes the slip of the materials during the bending process.
Hydraulic Guide Rolls can move towards three directions, to reduce the deformations and to facilitate bending processes, especially about angles and spirals.
There are private productions up to the customers’ demands on Big Profile Bending Machines, in addition to standard production. For instance;
- The distance between the rolls can be lengthened to increase the bending capability.
- Three rolls can be produced as driven by separate gearboxes and hydraulic motors. (Except APK 360 & 550 on which this system exists)
- The movement of lower rolls and the rotation movement can be done in the same time with some hydraulic arrangements.
- The lower rolls’, rotation’s and hydraulic guide rolls’ movements can be arranged according to each other.
- Placement of the hydraulic tank up to the customer’s demand.
- Assembling the control panel on the machine body.
- Lower rolls’ movements can be adjusted too slowly for sensitive bending.
- The bending speed can be increased.
FOR MORE INFORMATION SEE PRODUCT FEATURES TAB

EQUIPPED WITH:

Machine body is steel (ST-52) construction
On APK81 rolls are driven by a hydraulic motor+planetry gearbox and gears
Shafts made of special steel, hardened and grounded
One set standard rolls
Lower rolls hydraulic moveable up and down
Digital display for lower rolls
Separate and moveable control panel
Hydraulic guide rolls are moving in two directions
Manual lubrication
Horizontal & vertical working
Suitable for CE

OPTIONAL MODELS:
APK 81-DRO, Capacity: L3″ x 3″ x 5/16″ (In Stock) – $29,995.00
APK 81-NC, Capacity: L3″ x 3″ x 5/16″ – $50,000.00
APK 81-CNC, Capacity: L3″ x 3″ x 5/16″ – $52,000.00

SPECIFICATIONS:
Capacities: L3″ x 3″ x 5/16″
Max. section modulus: 1.0 in3
Roll Diameter Ø: 9.65″
Shaft Ø: 3.15″
Bending Speed: 14″ per/min
Motor Power (HP): 7.5 & 1
Length x Width x Height: 54″ x 41″ x 61″
Weight: 3,750 lbs.

*The dimensions can be changed according to the position of hydraulic tank.
*Data based upon steel 36,000 PSI yield point.
*Pictures shown in this offer are just for demonstration, might be with or without optional equipment

Specifications are subject to change without notice.
NOTE: Data is provided by the manufacturer.
WARRANTY: 1 YEAR

OPTIONAL ITEMS: CALL FOR PRICE
Special Guide Rolls for Angle Materials
Two Speeds
Variable speed of rotation
Hydraulic Guide Rolls
Digital Readout for Guide Rolls
NC Control System (AK 300CS3)
CNC Control System (AK 400CS3)
Digital Display for Hydraulic Guide Rolls: Digital displays show the positioning of hydraulic guide rolls which makes bending process easier for the operators. The maximum positions of hydraulic guide rolls can be limited from those control panels. So that hydraulic guide rolls do not go up to the maximum available positions.
Hydraulic Pulling System: While bending H-I-U profiles in hard-way, there occur a big force on weaker side of these profiles which results in enormous deformation. In order to prevent this deformation, hydraulic pulling system is developed by AKYAPAK. This system consists of hydraulic pulling arm, arm guide for channels, arm guide beams and special rolls suitable for bending H-I-U profiles.
Arm Guide: This equipment is mounted on the hydraulic pulling arm. Same arm guide can be used for H and I profiles. But it is necessary to use different arm guide for U profiles.
Arm Guide Rolls These equipments are mounted on the arm guide. These rolls are different according to each type and size of the profiles.
*CONTACT US FOR COMPLETE LIST OF OPTIONAL EQUIPMENT

The post AKYAPAK APK 81 3 x 3 x 3/8 in. Angle Bending Roll – Options Available appeared first on Sheet Metal Machines.

TENNSMITH F6-96-12 8 ft x 12 ga. Box and Pan Hand Brake

smm-admin — Tue, 23 May 2023 23:41:39 +0000

MADE IN USA
TENNSMITH’S F6 Series box and pan brakes were designed to provide heavy-duty forming capability, along with the flexibility of removable 6-inch box depth fingers. Ample clamping and easy-to-use nose bar adjustments allow for quick setting bend radius. Welded steel plate construction and heavy truss rods and braces provide strength and rigidity.

Other adjustment features include:

- Leveling screws and lock nuts on the pedestals
- Jack screws and tensioner bolts on the apron
- Truss rods on the apron, base and upper beam
- Fully adjustable counter balances to facilitate the bending process
- Removable apron angle and insert permit 1/4 inch reverse bends in lighter material.

SPECIFICATIONS:
Capacity – Mild Steel: 12 ga
Capacity – Stainless Steel: 16 ga
Bending Length: 96″
Maximum Lift of Beam: 2-1/4″
Front to Rear Beam Adjustment: 1/2″
Maximum Depth of Box: 6″
Minimum Reverse Bend: 1/4″
Minimum Flange in Capacity Material: 1″
Finger Widths: 3, 4 and 5 in.
Dimensions (LxWxH) Counterweights in Place: 137″ x 53″ x 60″
Shipping Weight: 3,250 lbs.

Specifications are subject to change without notice.
NOTE: Data is provided by the manufacturer.
WARRANTY: 3 YEAR – Limited

OPTIONAL ITEMS:

85270: Extension Fingers (pair) for F6 Models: $425.00
Right and left extension fingers form inside corners with a return flange across the top on boxes, cabinets, etc.
85275: Open End Fingers (pair) for F6 Models: $575.00
Provides triangular, square, tapered and rectangular tube forming abilities
85280: F6 Radius Fingers (Please Specify Radii) – per inch: $31.50

The post TENNSMITH F6-96-12 8 ft x 12 ga. Box and Pan Hand Brake appeared first on Sheet Metal Machines.

TIN KNOCKER Liner Table

smm-admin — Tue, 23 May 2023 19:40:11 +0000

The Tin Knocker manual insulation cutter slits fiberglass insulation to length and width.
Material is fed into the machine with a crank handle. The desired width is immediately cut with the adjustable slitter blade while the insulation is fed into the blade. The embedded scale makes for fast and accurate cutting
Once the material is at the desired length the operator pulls the handle, quickly and efficiently slitting the insulation to length with the crosscut blade.
The result is a simple and easy way to make repeatable cuts to fiberglass insulation.
Payoff reel, adjustable width
Quick cut slitter, length & width
Embedded scale for fast slitting to width
Exit table not included and this machines ships knocked down. Assembly is easy but please call Sheet Metal Machines at 386-304-3720 if you have any questions.

SPECIFICATIONS:
Overall width: 58
Width between end frames: 52-1/4″
Max Cutting Width: 48-1/2″
Table Height: 35″
Feed Speed: 60 FPM
Overall depth: 26″
Shaft Diameter: 3″
Knife Dimensions:: 5” OD x 1/4”
Motor HP: 3/4 HP
Electrics: 110/220V – 1ph
Ship Dimensions: 67” x 37” x 48”
Weight: 525 lbs.

Specifications are subject to change without notice.
NOTE: Data is provided by the manufacturer.
WARRANTY: 1 YEAR – Parts

The post TIN KNOCKER Liner Table appeared first on Sheet Metal Machines.

TENNSMITH 52H 4 ft x 16 ga. Hydraulic Shear – Options Available

smm-admin — Tue, 23 May 2023 19:39:22 +0000

MADE IN USA
TENNSMITH’S power shears combine all of the features of our foot shears with the advantage and convenience of air or hydraulic operation. TENNSMITH power shears are a productive addition to any shop. The air shears utilize heavy-duty, tie rod-type pneumatic cylinders, which provide up to 40 strokes per minute in capacity materials.
A foot-operated air valve control, pressure regulator, air gauge, oiler/condenser cups and neoprene, padded holddown feet are standard features. We recommend a maximum air supply of 75 psi for operating these shears at rated capacity. Where air supply pressures exceed 75 psi, an in-line regulator is helpful to provide pressure control.
The Model 52H cycle at 45 strokes a minute, thanks to its first class hydraulic system. The hydraulic unit is of a low maintenance design featuring a solenoid actuated valve, 3-HP electric motor, self-contained pump in tank with pressure gauge, check valve and industrial quality cylinders. The motor is protected by a magnetic starter.
Other electrical safety features include a low voltage on/off switch; low voltage, shrouded, electric foot switch; step-down transformer with low voltage circuit fuse; fully enclosed electrical box; and insulated reinforced conduit for all wiring. Models 36A and 52A are ideal ways to enhance shearing productivity with minimal investment.

OPTIONAL MODELS:
81080: 230V/3PH – $9,895.00
81090: 460V/3PH – $9,895.00
81100: 230V/1PH – $10,245.00

STANDARD EQUIPMENT:

High Carbon/High-Chromium (HCHC) Blades
Back gauge
Front extension arms with stop
Bevel gauge
Graduated side gauges
Foot control
Neoprene padded hold down feet

SPECIFICATIONS:
Operation: Hydraulic
Maximum shearing capacity, Mild Steel: 16 gauge/1.6mm
Maximum shearing capacity, Stainless Steel: 20 gauge/1.0mm
Maximum cutting length: 52-1/4″ / 1,327mm
Back gauge range: 30″ / 762mm
Front gauge range: 37″ / 940mm
Floor space, gauges in position: 60″ x 80″
Dimensions, Less gauges, LxWxH: 61″ x 25″ x 42″
Strokes per minute, full length: 45
Maximum Operating Pressure: 1,450 psi
Air Consumption per Stroke: N/A
Motor: 230 or 460V, 3ph, 60Hz, 1,745 RPM, 230V/1ph optional (specify): 5 HP
Shipping Weight: 1,300 lbs. / 590kg

Specifications are subject to change without notice.
NOTE: Data is provided by the manufacturer.
WARRANTY: 3 YEAR – Limited

OPTIONAL ITEMS:

Wired for CSA Canadian Electrical Standard ….. add $525.00
52 inch HCHC Blades, per set …………………… $975.00
81510: 4′ Squaring Arm ………..$950.00

The post TENNSMITH 52H 4 ft x 16 ga. Hydraulic Shear – Options Available appeared first on Sheet Metal Machines.

TENNSMITH Model 52 4ft x 16 ga. Foot-Squaring Shear

smm-admin — Tue, 23 May 2023 19:39:21 +0000

MADE IN USA
TENNSMITH’S squaring shears offer precision shearing and rugged construction at an affordable price. The shear frame, bed and cutter head assemblies are constructed of heavy-duty cast iron. The shear bed is machined and then surface ground to precision tolerances to ensure an accurate working surface.
These shears feature triaction, high-carbon/high chromium (HCHC) steel blades. Both the upper and lower blades have a 2 degree edge relief and the lower blade has an additional 1-degree face relief for maximum material penetration with minimum effort. Triaction blades help prevent material movement while shearing, prolonging blade life.
TENNSMITH shears have the most complete adjustment features of any sheet metal shear on the market. The lower shear blade is bed adjusting and the upper blade is adjustable by means of a truss bar on the cutter head. The spring-activated hold down feet clamp the work piece securely in place and are easily adjustable to compensate holding pressure for light or heavy gauge material. There is ample clearance between the hold down feet and shear blades to allow good operator vision for line-of-sight cutting. The standard, double-locking back gauge, which features embossed scales and vernier wheels for fine adjustment, gives highly accurate readings.

STANDARD EQUIPMENT:

Back gauge
Front extension arms with stop
Bevel gauge
Graduated side scales

SPECIFICATIONS:
Maximum shearing capacity, Mild Steel: 16 gauge/1.6mm
Maximum shearing capacity, Stainless Steel: 20 gauge/1.0mm
Maximum cutting length: 52-1/4″ / 1,327mm
Back gauge range: 30″ / 762mm
Front gauge range: 37″ / 940mm
Floor space, gauges in position: 60″ x 80″
Dimensions, less gauges, LxWxH: 61″ x 36″ x 42″
Shipping Weight: 950 lbs. / 431kg

Specifications are subject to change without notice.
NOTE: Data is provided by the manufacturer.
WARRANTY: 3 YEAR – Limited

Machine Photo May Include Optional Equipment
Product image is only a representation, actual product appearance may differ slightly

OPTIONAL ITEMS:

81510: Squaring Arm 4 Foot: $950.00
81555 – 52 inch HCHC Blades, per set ……………………… $975.00

The post TENNSMITH Model 52 4ft x 16 ga. Foot-Squaring Shear appeared first on Sheet Metal Machines.

TENNSMITH HBU48-16 4 ft x 16 ga. Bench-Mounted Box and Pan Hand Brake

smm-admin — Tue, 23 May 2023 19:39:12 +0000

MADE IN USA
TENNSMITH’S bench-mounted hand brakes are rugged, dependable USA-made tools that wont break your budget. Model HBU48-16 is a heavy-duty bench brake suitable for box and pan or straight bending in up to 16-gauge mild steel. The brake features a removable apron angle and apron insert permitting 1/4 inch reverse bends in lighter materials. The upper leaf and nose bar has a wide range of adjustment for radius bending. Standard equipment includes an apron stop rod for repeat bends, extension handles and a counterweight.
Model HBS48-16 is identical in features and capacity to the HBU48-16 but is intended solely for straight bending. Like our larger hand brakes, the HBS48-16 features a replaceable nose bar.
TENNSMITH’S bench-mounted hand brakes provide an economical means of performing a wide range of sheet metal bending and forming operations. These brakes are all-steel welded construction, readily adjustable and utilize bronze bearings at pivot points.

SPECIFICATIONS:
Capacity – Mild Steel: 16 ga
Bending Length: 48-1/4″
Maximum Depth of Box: 4″
Maximum Lift of Beam: 1-1/4″
Front to Rear Beam Adjustment: 5/8″
Minimum Reverse Bend: 1/4″
Minimum Flange in Capacity Material: 1″
Finger Widths: 2, 3, 4 in.
Shipping Weight: (lbs.): 495 lbs.

Specifications are subject to change without notice.
NOTE: Data is provided by the manufacturer.
WARRANTY: 3 YEAR – Limited

OPTIONAL ITEMS:

Floor Stand for 4 Foot Bench Brakes – $385.00

The post TENNSMITH HBU48-16 4 ft x 16 ga. Bench-Mounted Box and Pan Hand Brake appeared first on Sheet Metal Machines.

TIN KNOCKER TK24 24 Ga. Pittsburgh Roll Former with Stand

smm-admin — Tue, 23 May 2023 23:37:41 +0000

On the job site or in the shop, this portable little rollformer is a work horse for 24 gauge and lighter material. It is available with optional power flanging attachment and is perfect for field use. Steel stand included.
Portable rollformer is a work horse for 24 gauge and lighter material.
It is available with optional power flanging attachment and is perfect for field use.
With the included, all steel stand, it will also fit right in with your other shop equipment.
NOTE: When shipping, rollformer will fit inside stand

SPECIFICATIONS:
Capacity: 24 Gauge Mild Steel
Motor: 1/2 HP, 1700 RPM, 115 Volt, Single Phase, 60 Hz – Standard (Optional – 230v/1/50 available – please call)
Depth of Pocket: Approx. 5/16″ (7.9mm) with hammer edge of 3/8″ (9.53mm)
Speed: Approx. 35 FPM
Flange Height: 3/16″ (4.76mm)
Dimensions of Roll Former: 30″ x 14″ x 20″ (762mm x 356mm x 508mm)
Dimensions of Stand: 35″ x 14″ x 24″ (889mm x 483mm x 610mm) add 6″ around for shipping
Shipping Dimensions: 41″ x 25″ x 30″ (1,041mm x 65mm x 762mm)
Weight: Rollformer: 305 lbs

OPTIONAL MODEL:
TIN KNOCKER TK24 24 ga. Pittsburgh Roll Former w/Stand and Flanger Attachment = $3,550.00

OPTIONAL ITEMS:
20 or 24 gauge Flanging attachment = $985.00

Specifications are subject to change without notice.
NOTE: Data is provided by the manufacturer.
WARRANTY: 1 YEAR – Parts

The post TIN KNOCKER TK24 24 Ga. Pittsburgh Roll Former with Stand appeared first on Sheet Metal Machines.

TIN KNOCKER TK20 20 Ga. Pittsburgh Roll Former

smm-admin — Tue, 23 May 2023 19:37:05 +0000

A workhorse! The heart of any HVAC sheet metal shop. This 5 station 20 Gauge Pittsburgh lock roll former is offered with choice of Drive Cleat or Acme Rolls on the other outboard side. Powered by a 1 HP motor with V-belt drive, this machine is built for dependability.

5 station 20 Gauge Pittsburgh lock rollformer is offered with choice of Drive Cleat or Acme rolls on the other outboard side.
Powered by a 1 HP motor with V-belt drive
Built for dependability.

SPECIFICATIONS:
Capacity: 20 Gauge to 26 Gauge Mild Steel
Motor: 1 HP, 115/230 Volt, 1800 RPM
Speed: Approx. 25 FPM
Depth of Pocket: 5/16″ (7.9mm)
Dimensions: 40″L x 24″W x 44″H (1016mm x 610mm x 1118mm)
Weight: 360 lbs. (136kg)

Specifications are subject to change without notice.
NOTE: Data is provided by the manufacturer.
WARRANTY: 1 YEAR – Parts

The post TIN KNOCKER TK20 20 Ga. Pittsburgh Roll Former appeared first on Sheet Metal Machines.