- ** FREE SHIPPING TO COMMERCIAL ADDRESS THAT CAN OFFLOAD** SHIPPING IS TO LOWER 48 STATES ONLY. OTHER AREAS PLEASE EMAIL FOR FREIGHT QUOTES.
- Due to unprecedented rise in steel costs, the manufacturer is requiring ALL distributors to add a 17% steel surcharge to the base price of Betenbender Machines. Price shown is the base price.
Every Betenbender machine is thoroughly inspected and tested.
1.Parallelism is maintained between bed and ram or at preset angle by using precision automatic leveling controls. Parallelism is maintained at +/-.002″ in low speed.
2.The ram bottom reversal point is controlled by precise limit switches referenced off the bed. This isolates housing deflections, which can interfere with its accuracy.
- ENHANCED PRODUCTIVITY
Return speed and rapid advance facilitates high cycle rates. Operator control is simplified by slow and press speed, thus work spoilage is avoided. Rapid advance with automatic change. The point of speed change is fully adjustable by electric limit switch. Micrometer type tilt adjustment is graduated in .001″ increments permitting ram tilt adjustments up to 1/2″ in either direction.
- ELECTRO MECHANICAL STROKE CONTROL is bed referenced. Bottom limit is manually set with a lead screw and displayed by an mechanical readout calibrated in .001″ increments.
BETENBENDER’S press brakes have long full tonnage strokes, adjustable length and selectable speed combinations, adjustable height for short stroke, 2-speed standard and the optional 3- speed for adjustable low speed to prevent whip
- ELECRICAL EQUIPMENT
Meets requirements of NFPA no.79, JIC and construction requirements of the latest ANSI B-11.3 Standards. Includes drip-proof, continuous duty 45 degree Celsius ambient hydraulic pump motor wired for 230 or 460 volt, 3 phase 60 hertz.
Self-lubricating replaceable non-metallic ways prevent galling and provide long service life. Cylinders are high-strength, all steel. To minimize wear and provide a superior oil seal, inside cylinder surfaces are honed to a mirror finish.
Compact, precision machined aluminum manifold incorporates off-the shelf components, minimizes piping and consolidates “O” ring mounted valves.
Quiet, vane type, constant volume pumps. In keeping with good hydraulic design practice, these energy efficient pumps are located outside the reservoir.
Filtration of contaminants as small as 10 microns is accomplished with intake and discharge filters. A built-in magnetic trap and air breather filter provides added protection against contaminants. Reservoir of large capacity facilitates effective heat dissipation. A fluid level gauge is provided.
Main Control Cabinet – NEMA 12 enclosures mounted in the right housing containing: magnetic non-reversing motor starter and 120 volt circuit.
Main motor START button and STOP button are illuminated.
RAM UP and RAM DOWN buttons.
Clevis mounted cylinders eliminate cylinder binding by reducing the possibility of oil leaks from cylinder binding.
(Pins & bushings do not rotate under load, this reduces excessive wear)
- MADE IN USA
- Clamp Type Back-gauge-Manual Adjustable X,Y,Z
- NEMA Electrics
- All Hydraulic Fluid Included
- American Made Motor
- Hour Meter
- Lifetime Telephone Support @ No Charge
- Bottom Time Delay
- Three Position Foot Pedal
- Depth Stop w/Digital Readout
- All Steel Construction
- Disconnect Switch
- Two-Speed Ram
- All Components Available from Local Suppliers
Maximum Tonnage: 50 Tons
Maximum Bending Length: 144″
Distance Between Housings: 126-1/2″
Machine Weight: 12,500 lbs.
Motor Horsepower: 10
Overall Height: 104″
Overall Length: 159″
Overall Width: 45″
Specifications are subject to change without notice.
NOTE: Data is provided by the manufacturer.
WARRANTY: 1 YEAR – Parts
OPTIONAL ITEMS: CALL FOR PRICE
*Manual Front Reading Backgauge (24″) w/Mechanical Readout
Power Front Reading Backgauge w/5 Station NC “Go To” Controller on Pendant
Power Ram Adjustment w/5 Station NC “Go To” Controller on Pendant
Extra Length on Backgauge
Micrometer Precision Gauge Unit (2 Required)
CNC Ram Stop
*24″ Support Arms “Slide” Type
Extend Support Arms (each)
*Variable Tonnage Control
*One Shot Lubrication
*Light Curtain w/Full Fence
*Operator Station Palm Control
Additional Foot Pedal w/Key Lock
Palm Buttons/Foot Control System (Hand buttons to preset height, stop and hold, foot to continue to shut height.)
Dove Tails or T‑Slots
Bed Machining Angle Brackets
Angle Brackets (Plates) for Top (4″x4″) 18″ Shorter than Bed
Angle Brackets (Plates) for Bottom (4″x4″) 18″ Shorter than Bed
Increase Throat Gap or Increase Open Height
Increase Stroke Length
Die Rollover Bars (Recommended for 4/Way Dies)
Air Lift (Recommended for 4/Way Dies)
Crating Charge (Not An Export Crate) Still Requires Tarping
Special Paint Colors
Bolt/Shim Kit for Leveling
Ram Stop Control (1/4″ Above Die)
Rigging, Lagging, Leveling & Electrical Hook Up is Customers Responsibility
NOTE: DIE RISERS NOT FURNISHED
ASK ABOUT OPTIONS NOT LISTED.
ALL PRICES SUBJECT TO CHANGE WITHOUT NOTICE.