• MADE IN USA
• Frame: The frame is of open throat design with mounting holes in feet. Drilled and tapped holes in feet allow for leveling of the machine.
• Bed: The machined flat surface is slotted full length to accommodate standard die holders, filter blocks, misc.
• Front & Back of Bed: The bed is machined down 4” on the front and 12” on the back to allow a flat surface for mounting various brackets, supports and gauges.
• Ram: The ram is constructed of solid steel slotted to accept standard dies. The clamping bar is sectional for positive clamping. The upper is machined up to 4” to allow a flat surface for mounting brackets and gauges.
• Ram Tilt Adjustment: The micrometer spindle is located on the right side end frame of machine, which allows for adjustment of the desired angle required up to ±0.500 inch. The micrometer allows the operator to return to a given setting, parallel to desired angle. By using the micrometer reading, the machine can return to previous position.
• Ram Level: The ram level is accomplished by two hydraulic systems, one for each cylinder, which keeps them parallel. The ram self-levels at the bottom of each stroke even if hydraulic system is out of adjustment.
• Hydraulic Cylinders: Direct acting hydraulic cylinders are one piece, double acting with self-aligning, hardened ball sockets.
• Accuracy: Parallelism is maintained at ±0.002 inch in low speed.
• Operating Controls:
  • 1. Pull to start. Push off. Light is on when in the “ON” position.
  • 2. Run/Jog switch. Run position for normal operation. Jog position for loading of tooling, maintenance and set-up.
    Up/Down buttons are used when in jog.
  • 3. 3 Position Foot Petal
    a. Ram up
    b. Ram hold
    c. Foot petal down. Ram down allows or jogging of ram down and holding. Emergency stop and emergency up buttons are located on a small pedestal that comes from the foot petal.
  • 4. Cycle time delay at bottom of stroke
• *When using top & bottom tools on a press brake, a forming system is created which requires analysis to determine the appropriate safeguarding for operator safety and protection.
• *It is the user’s responsibility to ensure that the point of operation is effective and all applicable safety requirements are met.
• Stroke Control (Optional): Control of strokes in accomplished by rotation of hand wheels, which read in thousandths of an inch and set the closed height. When the machine is 2 or 3 speed, the knob for setting the speed change point is located on right side for simple adjustments.
• Tonnage Control (Optional): Our machines are equipped with optional adjustable
  tonnage control to go from lower tonnage to rated tonnage of machine, as well as overload protection.
• Backgauge: A slide and clamp, 3 axis backgauge 24” is standard.
  • 1. Front operated manual backgauge, hand wheel with mechanical readout (0.01)
  • 2. Front operated power backgauge with LED readout (0.001)
    CNC backgauging and front gauging is optional.
• Front Support Arms (Optional): 24” support arms are “slide” type. Optional disappearing stops help to hold the material from sliding backward.
• Electrical System: The electrical systems meet NFPA 79 standards. All machines have
  disconnect switches, magnetic starters, 110/120v controls, 208-230/460v 3 phase, others optional.
• Motors: Our American made motors are rated for continuous duty, open drip.
• Lubrication: Grease zerks are standard. One shot lube or automatic lubrication is optional.
• Safety Features: Betenbender Hydraulic Press Brakes and Shears are built to meet ANSI B11.3 standards. Safety features of the Betenbender Press Brake include:
  • Emergency stop on pedestal
  • Emergency up on pedestal
  • Warning signs, safety markings and covers
  • Electronics meet NFPA 79 standards
  • 110/120v control
• Specifications are subject to change withoutnotice.
• Compliance with OSHA requirements is the legal responsibility of the user and is subject to local inspectors’ interpretation of existing standards.
• Betenbender Shears are built to meet ANSI B11.3 standards

STANDARD EQUIPMENT:

• Clamp Type Backgauge-Manual Adjustment X, Y, and Z
• Two Speed Ram
• Bottom Time Delay
• Three Position Foot Pedal
• Depth Stop w/Digital Readout
• Three Speed (95T and Larger)
• American Made Motors
• Hour Meter
• Nema Electrics
• All Hydraulic Fluids Included
• Disconnect Switch
• All Steel Construction
• NOTE: DIE RISERS NOT FURNISHED

SPECIFICATIONS:
Overall Width (in.): 56-1/2
Width of Bed (in.): 5-1/2
Width of Upper Machined Ram (in.): 3-3/4
Overall Height (in.): 111
Throat Depth (in.): 8
Open Height (in.): 16
Closed Height (in.): 10
Height of Bed (in.): 37
Overall Length (in.): 183
Distance Between Housing (in.): 150-1/2
Width of Upper Ram (in.): 4
Width of Upper End Plates (in.): 60
Press (IPM): 25
Rapid Approach (IPM): 50
Return to Open (IPM): 70
2-Speed Electric Shift: Std.
HP: 30 HP, 208/230v, 80amps or 460v, 40amps (specify)
Weight (lbs.): 35,000

**ESTIMATED WEIGHTS. The weight of your machine may vary from the estimated weight listed here.
Weights may vary according to options included.
> For specs on larger machines please call or email us and we will provide those for you.
> All dimensions are in inches unless otherwise noted. (To convert to centimeters multiply by 2.54)
> Engineering data and dimensions are subject to change without notice due to continuing product development.
> Foundation plans are available upon request.
> Die Blocks are not furnished.
> To convert Horsepower to KW, multiply by 0.746

Specifications are subject to change without notice.
NOTE: Data is provided by the manufacturer.
WARRANTY: 1 YEAR – Parts

OPTIONAL ITEMS:

• Factory Start Up by Base Service Technician …… $1,250.00 per day plus expenses
• *24″ Support Arms “Slide” Type W/T-Slots …………………… $1,200.00 pair
• *Keylock Switch ……………………………………………………………. $300.00
• *Light Curtain ……………………………………………………………….. $7,500.00
• Manual Front Reading Backgauge (24”) with Mechanical Readout …. $CALL
• *One Shot Lubrication …………………………………………………. $1,100.00
• *Operator Station Palm Control …………………………………… $1,900.00
• *Variable Tonnage Control ………………………………………….. $1,550.00
• *Work Light ………………………………………………………………….. $450.00
• 208v Single Phase …………………………. $CALL
• Additional Foot Pedal with Keylock ……………………………… $CALL
• Air Lift (Recommended for 4/Way Dies ……………………….. $CALL
• Angle Brackets (Plates) for Bottom (4″x4″) 18″ Shorter than Bed ……. $300.00 per foot
• Angle Brackets (Plates) for Top (4″x4″) 18″ Shorter than Bed ……… $300.00 per foot
• Automatic Lubrication ………………………………………………….. $3,100.00 each
• Bed Machining Angle Brackets ……………………………………. $1,900.00
• Bolt/Shim Kit for Leveling  ……………………………………….. $450.00
• CNC Backgauge ……………………………. $CALL
• CNC Ram Stop ……………………………… $CALL
• Crating Charge (Not an Export Crate) Still Requires Tarping ….. P.O.R.
• Die Riser ……………………………………………………………… P.O.R.
• Die Rollover Bars (Recommended for 4/Way Dies) ….. $250.00
• Disappearing Stops (Support Arms) ……………………….. $200.00 each
• Dove Tails …………………………………….. $CALL
• Dual Calibration …………………………… $CALL
• Extended Support Arms (each) ………………………………… $60.00 per foot
• Extra Length on Backgauge ……………………………………… $CALL
• Extra Foot Pedal w/Keylock Switch …………………………… $1,000.00
• Increase Stroke Length ……………………………………………. P.O.R.
• Increase Throat Gap or Increase Open Height
  • 50, 70, 95 Ton ………….. $1,000.00 per inch
  • 120, 160, 190 Ton ……. $1,800.00 per inch
  • 240 Ton ……………………. $2,000.00 per inch
• Micrometer Precision Gauge Unit (2 Required) ……. $CALL
• Oil Cooler (Kidney Loop System) ……………………………… $7,500.00
• Palm Buttons/Foot Control System (Hand buttons to preset height, stop and hold, foot to continue to shut height) …………………………………………$3,100.00
• Power Front Reading Backgauge with 5 Station NC “GO-TO” Positioner on Pendant … $CALL
• Power Ram Adjustment with 5 Station NC “GO-TO” Positioner on Pendant …. $CALL
• Ram Machining ………………………………….. $1,900.00
• Ram Stop Control (1/4″ above die) ………….. P.O.R.
• Special Application Tooling ………….. $CALL
• Special Paint Colors …………………….. P.O.R.
• T-Slots ………………………………………….. $300.00 per foot
• BACKGAUGES AND RAM CONTROL:
  • *Manual Front Reading Backgauge (24″) w/Mechanical Readout ….. $3,500.00
  • Power Front Reading Backgauge w/5 Station NC “Go To” Positioner on Pendant …… $5,500.00
  • Power Ram Adjustment w/5 Station NC “Go To” Positioner on Pendant ……. $2,500.00
  • Extra Length on Backgauge ……………………….. $1,000.00
  • CNC Backgauge …………………………………………. P.O.R.

Rigging, Lagging, Leveling and Electrical Hook Up is Customers Responsibility
ASK ABOUT OPTIONS NOT LISTED.
ALL PRICES SUBJECT TO CHANGE WITHOUT NOTICE.
NOTE: DIE RISERS NOT FURNISHED
*RECOMMENDED OPTIONS

The post BETENBENDER 14ft x 240 Ton Hydraulic Press Brake | Model 14-240 appeared first on Sheet Metal Machines.

• MADE IN USA
• Frame: The frame is of open throat design with mounting holes in feet. Drilled and tapped holes in feet allow for leveling of the machine.
• Bed: The machined flat surface is slotted full length to accommodate standard die holders, filter blocks, misc.
• Front & Back of Bed: The bed is machined down 4” on the front and 12” on the back to allow a flat surface for mounting various brackets, supports and gauges.
• Ram: The ram is constructed of solid steel slotted to accept standard dies. The clamping bar is sectional for positive clamping. The upper is machined up to 4” to allow a flat surface for mounting brackets and gauges.
• Ram Tilt Adjustment: The micrometer spindle is located on the right side end frame of machine, which allows for adjustment of the desired angle required up to ±0.500 inch. The micrometer allows the operator to return to a given setting, parallel to desired angle. By using the micrometer reading, the machine can return to previous position.
• Ram Level: The ram level is accomplished by two hydraulic systems, one for each cylinder, which keeps them parallel. The ram self-levels at the bottom of each stroke even if hydraulic system is out of adjustment.
• Hydraulic Cylinders: Direct acting hydraulic cylinders are one piece, double acting with self-aligning, hardened ball sockets.
• Accuracy: Parallelism is maintained at ±0.002 inch in low speed.
• Operating Controls:
  • 1. Pull to start. Push off. Light is on when in the “ON” position.
  • 2. Run/Jog switch. Run position for normal operation. Jog position for loading of tooling, maintenance and set-up.
    Up/Down buttons are used when in jog.
  • 3. 3 Position Foot Petal
    a. Ram up
    b. Ram hold
    c. Foot petal down. Ram down allows or jogging of ram down and holding. Emergency stop and emergency up buttons are located on a small pedestal that comes from the foot petal.
  • 4. Cycle time delay at bottom of stroke
• *When using top & bottom tools on a press brake, a forming system is created which requires analysis to determine the appropriate safeguarding for operator safety and protection.
• *It is the user’s responsibility to ensure that the point of operation is effective and all applicable safety requirements are met.
• Stroke Control (Optional): Control of strokes in accomplished by rotation of hand wheels, which read in thousandths of an inch and set the closed height. When the machine is 2 or 3 speed, the knob for setting the speed change point is located on right side for simple adjustments.
• Tonnage Control (Optional): Our machines are equipped with optional adjustable
  tonnage control to go from lower tonnage to rated tonnage of machine, as well as overload protection.
• Backgauge: A slide and clamp, 3 axis backgauge 24” is standard.
  • 1. Front operated manual backgauge, hand wheel with mechanical readout (0.01)
  • 2. Front operated power backgauge with LED readout (0.001)
    CNC backgauging and front gauging is optional.
• Front Support Arms (Optional): 24” support arms are “slide” type. Optional disappearing stops help to hold the material from sliding backward.
• Electrical System: The electrical systems meet NFPA 79 standards. All machines have
  disconnect switches, magnetic starters, 110/120v controls, 208-230/460v 3 phase, others optional.
• Motors: Our American made motors are rated for continuous duty, open drip.
• Lubrication: Grease zerks are standard. One shot lube or automatic lubrication is optional.
• Safety Features: Betenbender Hydraulic Press Brakes and Shears are built to meet ANSI B11.3 standards. Safety features of the Betenbender Press Brake include:
  • Emergency stop on pedestal
  • Emergency up on pedestal
  • Warning signs, safety markings and covers
  • Electronics meet NFPA 79 standards
  • 110/120v control
• Specifications are subject to change withoutnotice.
• Compliance with OSHA requirements is the legal responsibility of the user and is subject to local inspectors’ interpretation of existing standards.
• Betenbender Shears are built to meet ANSI B11.3 standards

STANDARD EQUIPMENT:

• Clamp Type Backgauge-Manual Adjustment X, Y, and Z
• Two Speed Ram
• Bottom Time Delay
• Three Position Foot Pedal
• Depth Stop w/Digital Readout
• Three Speed (95T and Larger)
• American Made Motors
• Hour Meter
• Nema Electrics
• All Hydraulic Fluids Included
• Disconnect Switch
• All Steel Construction
• NOTE: DIE RISERS NOT FURNISHED

SPECIFICATIONS:
Overall Width (in.): 56-1/2
Width of Bed (in.): 5
Width of Upper Machined Ram (in.): 2-3/4
Overall Height (in.): 103
Throat Depth (in.): 8
Open Height (in.): 14
Closed Height (in.): 6
Height of Bed (in.): 37
Overall Length (in.): 183
Distance Between Housing (in.): 150-1/2
Width of Upper Ram (in.): 3
Width of Upper End Plates (in.): 50
Press (IPM): 25
Rapid Approach (IPM): 55
Return to Open (IPM): 66
2-Speed Electric Shift: Std.
HP: 20 HP, 208/230v, 54amps or 460v, 27 amps (specify)
Weight (lbs.): 27,000

**ESTIMATED WEIGHTS. The weight of your machine may vary from the estimated weight listed here.
Weights may vary according to options included.
> For specs on larger machines please call or email us and we will provide those for you.
> All dimensions are in inches unless otherwise noted. (To convert to centimeters multiply by 2.54)
> Engineering data and dimensions are subject to change without notice due to continuing product development.
> Foundation plans are available upon request.
> Die Blocks are not furnished.
> To convert Horsepower to KW, multiply by 0.746

Specifications are subject to change without notice.
NOTE: Data is provided by the manufacturer.
WARRANTY: 1 YEAR – Parts

OPTIONAL ITEMS:

• Factory Start Up by Base Service Technician …… $1,250.00 per day plus expenses
• *24″ Support Arms “Slide” Type W/T-Slots …………………… $1,200.00 pair
• *Keylock Switch ……………………………………………………………. $300.00
• *Light Curtain ……………………………………………………………….. $7,500.00
• Manual Front Reading Backgauge (24”) with Mechanical Readout …. $CALL
• *One Shot Lubrication …………………………………………………. $1,100.00
• *Operator Station Palm Control …………………………………… $1,900.00
• *Variable Tonnage Control ………………………………………….. $1,550.00
• *Work Light ………………………………………………………………….. $450.00
• 208v Single Phase …………………………. $CALL
• Additional Foot Pedal with Keylock ……………………………… $CALL
• Air Lift (Recommended for 4/Way Dies ……………………….. $CALL
• Angle Brackets (Plates) for Bottom (4″x4″) 18″ Shorter than Bed ……. $300.00 per foot
• Angle Brackets (Plates) for Top (4″x4″) 18″ Shorter than Bed ……… $300.00 per foot
• Automatic Lubrication ………………………………………………….. $3,100.00 each
• Bed Machining Angle Brackets ……………………………………. $1,900.00
• Bolt/Shim Kit for Leveling  ……………………………………….. $450.00
• CNC Backgauge ……………………………. $CALL
• CNC Ram Stop ……………………………… $CALL
• Crating Charge (Not an Export Crate) Still Requires Tarping ….. P.O.R.
• Die Riser ……………………………………………………………… P.O.R.
• Die Rollover Bars (Recommended for 4/Way Dies) ….. $250.00
• Disappearing Stops (Support Arms) ……………………….. $200.00 each
• Dove Tails …………………………………….. $CALL
• Dual Calibration …………………………… $CALL
• Extended Support Arms (each) ………………………………… $60.00 per foot
• Extra Length on Backgauge ……………………………………… $CALL
• Extra Foot Pedal w/Keylock Switch …………………………… $1,000.00
• Increase Stroke Length ……………………………………………. P.O.R.
• Increase Throat Gap or Increase Open Height
  • 50, 70, 95 Ton ………….. $1,000.00 per inch
  • 120, 160, 190 Ton ……. $1,800.00 per inch
  • 240 Ton ……………………. $2,000.00 per inch
• Micrometer Precision Gauge Unit (2 Required) ……. $CALL
• Oil Cooler (Kidney Loop System) ……………………………… $7,500.00
• Palm Buttons/Foot Control System (Hand buttons to preset height, stop and hold, foot to continue to shut height) …………………………………………$3,100.00
• Power Front Reading Backgauge with 5 Station NC “GO-TO” Positioner on Pendant … $CALL
• Power Ram Adjustment with 5 Station NC “GO-TO” Positioner on Pendant …. $CALL
• Ram Machining ………………………………….. $1,900.00
• Ram Stop Control (1/4″ above die) ………….. P.O.R.
• Special Application Tooling ………….. $CALL
• Special Paint Colors …………………….. P.O.R.
• T-Slots ………………………………………….. $300.00 per foot
• BACKGAUGES AND RAM CONTROL:
  • *Manual Front Reading Backgauge (24″) w/Mechanical Readout ….. $3,500.00
  • Power Front Reading Backgauge w/5 Station NC “Go To” Positioner on Pendant …… $5,500.00
  • Power Ram Adjustment w/5 Station NC “Go To” Positioner on Pendant ……. $2,500.00
  • Extra Length on Backgauge ……………………….. $1,000.00
  • CNC Backgauge …………………………………………. P.O.R.

Rigging, Lagging, Leveling and Electrical Hook Up is Customers Responsibility
ASK ABOUT OPTIONS NOT LISTED.
ALL PRICES SUBJECT TO CHANGE WITHOUT NOTICE.
NOTE: DIE RISERS NOT FURNISHED
*RECOMMENDED OPTIONS

The post BETENBENDER 14ft x 190 Ton Hydraulic Press Brake | Model 14-190 appeared first on Sheet Metal Machines.

• MADE IN USA
• Frame: The frame is of open throat design with mounting holes in feet. Drilled and tapped holes in feet allow for leveling of the machine.
• Bed: The machined flat surface is slotted full length to accommodate standard die holders, filter blocks, misc.
• Front & Back of Bed: The bed is machined down 4” on the front and 12” on the back to allow a flat surface for mounting various brackets, supports and gauges.
• Ram: The ram is constructed of solid steel slotted to accept standard dies. The clamping bar is sectional for positive clamping. The upper is machined up to 4” to allow a flat surface for mounting brackets and gauges.
• Ram Tilt Adjustment: The micrometer spindle is located on the right side end frame of machine, which allows for adjustment of the desired angle required up to ±0.500 inch. The micrometer allows the operator to return to a given setting, parallel to desired angle. By using the micrometer reading, the machine can return to previous position.
• Ram Level: The ram level is accomplished by two hydraulic systems, one for each cylinder, which keeps them parallel. The ram self-levels at the bottom of each stroke even if hydraulic system is out of adjustment.
• Hydraulic Cylinders: Direct acting hydraulic cylinders are one piece, double acting with self-aligning, hardened ball sockets.
• Accuracy: Parallelism is maintained at ±0.002 inch in low speed.
• Operating Controls:
  • 1. Pull to start. Push off. Light is on when in the “ON” position.
  • 2. Run/Jog switch. Run position for normal operation. Jog position for loading of tooling, maintenance and set-up.
    Up/Down buttons are used when in jog.
  • 3. 3 Position Foot Petal
    a. Ram up
    b. Ram hold
    c. Foot petal down. Ram down allows or jogging of ram down and holding. Emergency stop and emergency up buttons are located on a small pedestal that comes from the foot petal.
  • 4. Cycle time delay at bottom of stroke
• *When using top & bottom tools on a press brake, a forming system is created which requires analysis to determine the appropriate safeguarding for operator safety and protection.
• *It is the user’s responsibility to ensure that the point of operation is effective and all applicable safety requirements are met.
• Stroke Control (Optional): Control of strokes in accomplished by rotation of hand wheels, which read in thousandths of an inch and set the closed height. When the machine is 2 or 3 speed, the knob for setting the speed change point is located on right side for simple adjustments.
• Tonnage Control (Optional): Our machines are equipped with optional adjustable
  tonnage control to go from lower tonnage to rated tonnage of machine, as well as overload protection.
• Backgauge: A slide and clamp, 3 axis backgauge 24” is standard.
  • 1. Front operated manual backgauge, hand wheel with mechanical readout (0.01)
  • 2. Front operated power backgauge with LED readout (0.001)
    CNC backgauging and front gauging is optional.
• Front Support Arms (Optional): 24” support arms are “slide” type. Optional disappearing stops help to hold the material from sliding backward.
• Electrical System: The electrical systems meet NFPA 79 standards. All machines have
  disconnect switches, magnetic starters, 110/120v controls, 208-230/460v 3 phase, others optional.
• Motors: Our American made motors are rated for continuous duty, open drip.
• Lubrication: Grease zerks are standard. One shot lube or automatic lubrication is optional.
• Safety Features: Betenbender Hydraulic Press Brakes and Shears are built to meet ANSI B11.3 standards. Safety features of the Betenbender Press Brake include:
  • Emergency stop on pedestal
  • Emergency up on pedestal
  • Warning signs, safety markings and covers
  • Electronics meet NFPA 79 standards
  • 110/120v control
• Specifications are subject to change withoutnotice.
• Compliance with OSHA requirements is the legal responsibility of the user and is subject to local inspectors’ interpretation of existing standards.
• Betenbender Shears are built to meet ANSI B11.3 standards

STANDARD EQUIPMENT:

• Clamp Type Backgauge-Manual Adjustment X, Y, and Z
• Two Speed Ram
• Bottom Time Delay
• Three Position Foot Pedal
• Depth Stop w/Digital Readout
• Three Speed (95T and Larger)
• American Made Motors
• Hour Meter
• Nema Electrics
• All Hydraulic Fluids Included
• Disconnect Switch
• All Steel Construction
• NOTE: DIE RISERS NOT FURNISHED

SPECIFICATIONS:
Overall Width (in.): 56-1/2
Width of Bed (in.): 5
Width of Upper Machined Ram (in.): 2-3/4
Overall Height (in.): 103
Throat Depth (in.): 8
Open Height (in.): 14
Closed Height (in.): 6
Height of Bed (in.): 37
Overall Length (in.): 183
Distance Between Housing (in.): 150-1/2
Width of Upper Ram (in.): 3
Width of Upper End Plates (in.): 50
Press (IPM): 31
Rapid Approach (IPM): 68
Return to Open (IPM): 86
2-Speed Electric Shift: Std.
HP: 20 HP, 208/230v, 54amps or 460v, 27 amps (specify)
Weight (lbs.): 26,000

**ESTIMATED WEIGHTS. The weight of your machine may vary from the estimated weight listed here.
Weights may vary according to options included.
> For specs on larger machines please call or email us and we will provide those for you.
> All dimensions are in inches unless otherwise noted. (To convert to centimeters multiply by 2.54)
> Engineering data and dimensions are subject to change without notice due to continuing product development.
> Foundation plans are available upon request.
> Die Blocks are not furnished.
> To convert Horsepower to KW, multiply by 0.746

Specifications are subject to change without notice.
NOTE: Data is provided by the manufacturer.
WARRANTY: 1 YEAR – Parts

OPTIONAL ITEMS:

• Factory Start Up by Base Service Technician …… $1,250.00 per day plus expenses
• *24″ Support Arms “Slide” Type W/T-Slots …………………… $1,200.00 pair
• *Keylock Switch ……………………………………………………………. $300.00
• *Light Curtain ……………………………………………………………….. $7,500.00
• Manual Front Reading Backgauge (24”) with Mechanical Readout …. $CALL
• *One Shot Lubrication …………………………………………………. $1,100.00
• *Operator Station Palm Control …………………………………… $1,900.00
• *Variable Tonnage Control ………………………………………….. $1,550.00
• *Work Light ………………………………………………………………….. $450.00
• 208v Single Phase …………………………. $CALL
• Additional Foot Pedal with Keylock ……………………………… $CALL
• Air Lift (Recommended for 4/Way Dies ……………………….. $CALL
• Angle Brackets (Plates) for Bottom (4″x4″) 18″ Shorter than Bed ……. $300.00 per foot
• Angle Brackets (Plates) for Top (4″x4″) 18″ Shorter than Bed ……… $300.00 per foot
• Automatic Lubrication ………………………………………………….. $3,100.00 each
• Bed Machining Angle Brackets ……………………………………. $1,900.00
• Bolt/Shim Kit for Leveling  ……………………………………….. $450.00
• CNC Backgauge ……………………………. $CALL
• CNC Ram Stop ……………………………… $CALL
• Crating Charge (Not an Export Crate) Still Requires Tarping ….. P.O.R.
• Die Riser ……………………………………………………………… P.O.R.
• Die Rollover Bars (Recommended for 4/Way Dies) ….. $250.00
• Disappearing Stops (Support Arms) ……………………….. $200.00 each
• Dove Tails …………………………………….. $CALL
• Dual Calibration …………………………… $CALL
• Extended Support Arms (each) ………………………………… $60.00 per foot
• Extra Length on Backgauge ……………………………………… $CALL
• Extra Foot Pedal w/Keylock Switch …………………………… $1,000.00
• Increase Stroke Length ……………………………………………. P.O.R.
• Increase Throat Gap or Increase Open Height
  • 50, 70, 95 Ton ………….. $1,000.00 per inch
  • 120, 160, 190 Ton ……. $1,800.00 per inch
  • 240 Ton ……………………. $2,000.00 per inch
• Micrometer Precision Gauge Unit (2 Required) ……. $CALL
• Oil Cooler (Kidney Loop System) ……………………………… $7,500.00
• Palm Buttons/Foot Control System (Hand buttons to preset height, stop and hold, foot to continue to shut height) …………………………………………$3,100.00
• Power Front Reading Backgauge with 5 Station NC “GO-TO” Positioner on Pendant … $CALL
• Power Ram Adjustment with 5 Station NC “GO-TO” Positioner on Pendant …. $CALL
• Ram Machining ………………………………….. $1,900.00
• Ram Stop Control (1/4″ above die) ………….. P.O.R.
• Special Application Tooling ………….. $CALL
• Special Paint Colors …………………….. P.O.R.
• T-Slots ………………………………………….. $300.00 per foot
• BACKGAUGES AND RAM CONTROL:
  • *Manual Front Reading Backgauge (24″) w/Mechanical Readout ….. $3,500.00
  • Power Front Reading Backgauge w/5 Station NC “Go To” Positioner on Pendant …… $5,500.00
  • Power Ram Adjustment w/5 Station NC “Go To” Positioner on Pendant ……. $2,500.00
  • Extra Length on Backgauge ……………………….. $1,000.00
  • CNC Backgauge …………………………………………. P.O.R.

Rigging, Lagging, Leveling and Electrical Hook Up is Customers Responsibility
ASK ABOUT OPTIONS NOT LISTED.
ALL PRICES SUBJECT TO CHANGE WITHOUT NOTICE.
NOTE: DIE RISERS NOT FURNISHED
*RECOMMENDED OPTIONS

The post BETENBENDER 14ft x 160 Ton Hydraulic Press Brake | Model 14-160 appeared first on Sheet Metal Machines.

• MADE IN USA
• Frame: The frame is of open throat design with mounting holes in feet. Drilled and tapped holes in feet allow for leveling of the machine.
• Bed: The machined flat surface is slotted full length to accommodate standard die holders, filter blocks, misc.
• Front & Back of Bed: The bed is machined down 4” on the front and 12” on the back to allow a flat surface for mounting various brackets, supports and gauges.
• Ram: The ram is constructed of solid steel slotted to accept standard dies. The clamping bar is sectional for positive clamping. The upper is machined up to 4” to allow a flat surface for mounting brackets and gauges.
• Ram Tilt Adjustment: The micrometer spindle is located on the right side end frame of machine, which allows for adjustment of the desired angle required up to ±0.500 inch. The micrometer allows the operator to return to a given setting, parallel to desired angle. By using the micrometer reading, the machine can return to previous position.
• Ram Level: The ram level is accomplished by two hydraulic systems, one for each cylinder, which keeps them parallel. The ram self-levels at the bottom of each stroke even if hydraulic system is out of adjustment.
• Hydraulic Cylinders: Direct acting hydraulic cylinders are one piece, double acting with self-aligning, hardened ball sockets.
• Accuracy: Parallelism is maintained at ±0.002 inch in low speed.
• Operating Controls:
  • 1. Pull to start. Push off. Light is on when in the “ON” position.
  • 2. Run/Jog switch. Run position for normal operation. Jog position for loading of tooling, maintenance and set-up.
    Up/Down buttons are used when in jog.
  • 3. 3 Position Foot Petal
    a. Ram up
    b. Ram hold
    c. Foot petal down. Ram down allows or jogging of ram down and holding. Emergency stop and emergency up buttons are located on a small pedestal that comes from the foot petal.
  • 4. Cycle time delay at bottom of stroke
• *When using top & bottom tools on a press brake, a forming system is created which requires analysis to determine the appropriate safeguarding for operator safety and protection.
• *It is the user’s responsibility to ensure that the point of operation is effective and all applicable safety requirements are met.
• Stroke Control (Optional): Control of strokes in accomplished by rotation of hand wheels, which read in thousandths of an inch and set the closed height. When the machine is 2 or 3 speed, the knob for setting the speed change point is located on right side for simple adjustments.
• Tonnage Control (Optional): Our machines are equipped with optional adjustable
  tonnage control to go from lower tonnage to rated tonnage of machine, as well as overload protection.
• Backgauge: A slide and clamp, 3 axis backgauge 24” is standard.
  • 1. Front operated manual backgauge, hand wheel with mechanical readout (0.01)
  • 2. Front operated power backgauge with LED readout (0.001)
    CNC backgauging and front gauging is optional.
• Front Support Arms (Optional): 24” support arms are “slide” type. Optional disappearing stops help to hold the material from sliding backward.
• Electrical System: The electrical systems meet NFPA 79 standards. All machines have
  disconnect switches, magnetic starters, 110/120v controls, 208-230/460v 3 phase, others optional.
• Motors: Our American made motors are rated for continuous duty, open drip.
• Lubrication: Grease zerks are standard. One shot lube or automatic lubrication is optional.
• Safety Features: Betenbender Hydraulic Press Brakes and Shears are built to meet ANSI B11.3 standards. Safety features of the Betenbender Press Brake include:
  • Emergency stop on pedestal
  • Emergency up on pedestal
  • Warning signs, safety markings and covers
  • Electronics meet NFPA 79 standards
  • 110/120v control
• Specifications are subject to change withoutnotice.
• Compliance with OSHA requirements is the legal responsibility of the user and is subject to local inspectors’ interpretation of existing standards.
• Betenbender Shears are built to meet ANSI B11.3 standards

STANDARD EQUIPMENT:

• Clamp Type Backgauge-Manual Adjustment X, Y, and Z
• Two Speed Ram
• Bottom Time Delay
• Three Position Foot Pedal
• Depth Stop w/Digital Readout
• Three Speed (95T and Larger)
• American Made Motors
• Hour Meter
• Nema Electrics
• All Hydraulic Fluids Included
• Disconnect Switch
• All Steel Construction
• NOTE: DIE RISERS NOT FURNISHED

SPECIFICATIONS:
Overall Width (in.): 56-1/2
Width of Bed (in.): 5
Width of Upper Machined Ram (in.): 2-3/4
Overall Height (in.): 103
Throat Depth (in.): 8
Open Height (in.): 14
Closed Height (in.): 6
Height of Bed (in.): 37
Overall Length (in.): 207
Distance Between Housing (in.):174-1/2
Width of Upper Ram (in.): 3
Width of Upper End Plates (in.): 50
Press (IPM): 40
Rapid Approach (IPM): 87
Return to Open (IPM): 115
2-Speed Electric Shift: Std.
HP: 20 HP, 208/230v, 54amps or 460v, 27 amps (specify)
Weight (lbs.): 28,000

**ESTIMATED WEIGHTS. The weight of your machine may vary from the estimated weight listed here.
Weights may vary according to options included.
> For specs on larger machines please call or email us and we will provide those for you.
> All dimensions are in inches unless otherwise noted. (To convert to centimeters multiply by 2.54)
> Engineering data and dimensions are subject to change without notice due to continuing product development.
> Foundation plans are available upon request.
> Die Blocks are not furnished.
> To convert Horsepower to KW, multiply by 0.746

Specifications are subject to change without notice.
NOTE: Data is provided by the manufacturer.
WARRANTY: 1 YEAR – Parts

OPTIONAL ITEMS:

• Factory Start Up by Base Service Technician …… $1,250.00 per day plus expenses
• *24″ Support Arms “Slide” Type W/T-Slots …………………… $1,200.00 pair
• *Keylock Switch ……………………………………………………………. $300.00
• *Light Curtain ……………………………………………………………….. $7,500.00
• Manual Front Reading Backgauge (24”) with Mechanical Readout …. $CALL
• *One Shot Lubrication …………………………………………………. $1,100.00
• *Operator Station Palm Control …………………………………… $1,900.00
• *Variable Tonnage Control ………………………………………….. $1,550.00
• *Work Light ………………………………………………………………….. $450.00
• 208v Single Phase …………………………. $CALL
• Additional Foot Pedal with Keylock ……………………………… $CALL
• Air Lift (Recommended for 4/Way Dies ……………………….. $CALL
• Angle Brackets (Plates) for Bottom (4″x4″) 18″ Shorter than Bed ……. $300.00 per foot
• Angle Brackets (Plates) for Top (4″x4″) 18″ Shorter than Bed ……… $300.00 per foot
• Automatic Lubrication ………………………………………………….. $3,100.00 each
• Bed Machining Angle Brackets ……………………………………. $1,900.00
• Bolt/Shim Kit for Leveling  ……………………………………….. $450.00
• CNC Backgauge ……………………………. $CALL
• CNC Ram Stop ……………………………… $CALL
• Crating Charge (Not an Export Crate) Still Requires Tarping ….. P.O.R.
• Die Riser ……………………………………………………………… P.O.R.
• Die Rollover Bars (Recommended for 4/Way Dies) ….. $250.00
• Disappearing Stops (Support Arms) ……………………….. $200.00 each
• Dove Tails …………………………………….. $CALL
• Dual Calibration …………………………… $CALL
• Extended Support Arms (each) ………………………………… $60.00 per foot
• Extra Length on Backgauge ……………………………………… $CALL
• Extra Foot Pedal w/Keylock Switch …………………………… $1,000.00
• Increase Stroke Length ……………………………………………. P.O.R.
• Increase Throat Gap or Increase Open Height
  • 50, 70, 95 Ton ………….. $1,000.00 per inch
  • 120, 160, 190 Ton ……. $1,800.00 per inch
  • 240 Ton ……………………. $2,000.00 per inch
• Micrometer Precision Gauge Unit (2 Required) ……. $CALL
• Oil Cooler (Kidney Loop System) ……………………………… $7,500.00
• Palm Buttons/Foot Control System (Hand buttons to preset height, stop and hold, foot to continue to shut height) …………………………………………$3,100.00
• Power Front Reading Backgauge with 5 Station NC “GO-TO” Positioner on Pendant … $CALL
• Power Ram Adjustment with 5 Station NC “GO-TO” Positioner on Pendant …. $CALL
• Ram Machining ………………………………….. $1,900.00
• Ram Stop Control (1/4″ above die) ………….. P.O.R.
• Special Application Tooling ………….. $CALL
• Special Paint Colors …………………….. P.O.R.
• T-Slots ………………………………………….. $300.00 per foot
• BACKGAUGES AND RAM CONTROL:
  • *Manual Front Reading Backgauge (24″) w/Mechanical Readout ….. $3,500.00
  • Power Front Reading Backgauge w/5 Station NC “Go To” Positioner on Pendant …… $5,500.00
  • Power Ram Adjustment w/5 Station NC “Go To” Positioner on Pendant ……. $2,500.00
  • Extra Length on Backgauge ……………………….. $1,000.00
  • CNC Backgauge …………………………………………. P.O.R.

Rigging, Lagging, Leveling and Electrical Hook Up is Customers Responsibility
ASK ABOUT OPTIONS NOT LISTED.
ALL PRICES SUBJECT TO CHANGE WITHOUT NOTICE.
NOTE: DIE RISERS NOT FURNISHED
*RECOMMENDED OPTIONS

The post BETENBENDER 16ft x 120 Ton Hydraulic Press Brake | Model 16-120 appeared first on Sheet Metal Machines.

• MADE IN USA
• Frame: The frame is of open throat design with mounting holes in feet. Drilled and tapped holes in feet allow for leveling of the machine.
• Bed: The machined flat surface is slotted full length to accommodate standard die holders, filter blocks, misc.
• Front & Back of Bed: The bed is machined down 4” on the front and 12” on the back to allow a flat surface for mounting various brackets, supports and gauges.
• Ram: The ram is constructed of solid steel slotted to accept standard dies. The clamping bar is sectional for positive clamping. The upper is machined up to 4” to allow a flat surface for mounting brackets and gauges.
• Ram Tilt Adjustment: The micrometer spindle is located on the right side end frame of machine, which allows for adjustment of the desired angle required up to ±0.500 inch. The micrometer allows the operator to return to a given setting, parallel to desired angle. By using the micrometer reading, the machine can return to previous position.
• Ram Level: The ram level is accomplished by two hydraulic systems, one for each cylinder, which keeps them parallel. The ram self-levels at the bottom of each stroke even if hydraulic system is out of adjustment.
• Hydraulic Cylinders: Direct acting hydraulic cylinders are one piece, double acting with self-aligning, hardened ball sockets.
• Accuracy: Parallelism is maintained at ±0.002 inch in low speed.
• Operating Controls:
  • 1. Pull to start. Push off. Light is on when in the “ON” position.
  • 2. Run/Jog switch. Run position for normal operation. Jog position for loading of tooling, maintenance and set-up.
    Up/Down buttons are used when in jog.
  • 3. 3 Position Foot Petal
    a. Ram up
    b. Ram hold
    c. Foot petal down. Ram down allows or jogging of ram down and holding. Emergency stop and emergency up buttons are located on a small pedestal that comes from the foot petal.
  • 4. Cycle time delay at bottom of stroke
• *When using top & bottom tools on a press brake, a forming system is created which requires analysis to determine the appropriate safeguarding for operator safety and protection.
• *It is the user’s responsibility to ensure that the point of operation is effective and all applicable safety requirements are met.
• Stroke Control (Optional): Control of strokes in accomplished by rotation of hand wheels, which read in thousandths of an inch and set the closed height. When the machine is 2 or 3 speed, the knob for setting the speed change point is located on right side for simple adjustments.
• Tonnage Control (Optional): Our machines are equipped with optional adjustable
  tonnage control to go from lower tonnage to rated tonnage of machine, as well as overload protection.
• Backgauge: A slide and clamp, 3 axis backgauge 24” is standard.
  • 1. Front operated manual backgauge, hand wheel with mechanical readout (0.01)
  • 2. Front operated power backgauge with LED readout (0.001)
    CNC backgauging and front gauging is optional.
• Front Support Arms (Optional): 24” support arms are “slide” type. Optional disappearing stops help to hold the material from sliding backward.
• Electrical System: The electrical systems meet NFPA 79 standards. All machines have
  disconnect switches, magnetic starters, 110/120v controls, 208-230/460v 3 phase, others optional.
• Motors: Our American made motors are rated for continuous duty, open drip.
• Lubrication: Grease zerks are standard. One shot lube or automatic lubrication is optional.
• Safety Features: Betenbender Hydraulic Press Brakes and Shears are built to meet ANSI B11.3 standards. Safety features of the Betenbender Press Brake include:
  • Emergency stop on pedestal
  • Emergency up on pedestal
  • Warning signs, safety markings and covers
  • Electronics meet NFPA 79 standards
  • 110/120v control
• Specifications are subject to change withoutnotice.
• Compliance with OSHA requirements is the legal responsibility of the user and is subject to local inspectors’ interpretation of existing standards.
• Betenbender Shears are built to meet ANSI B11.3 standards

STANDARD EQUIPMENT:

• Clamp Type Backgauge-Manual Adjustment X, Y, and Z
• Two Speed Ram
• Bottom Time Delay
• Three Position Foot Pedal
• Depth Stop w/Digital Readout
• Three Speed (95T and Larger)
• American Made Motors
• Hour Meter
• Nema Electrics
• All Hydraulic Fluids Included
• Disconnect Switch
• All Steel Construction
• NOTE: DIE RISERS NOT FURNISHED

SPECIFICATIONS:
Overall Width (in.): 56-1/2
Width of Bed (in.): 5
Width of Upper Machined Ram (in.): 2-3/4
Overall Height (in.): 103
Throat Depth (in.): 8
Open Height (in.): 14
Closed Height (in.): 6
Height of Bed (in.): 37
Overall Length (in.): 183
Distance Between Housing (in.): 150-1/2
Width of Upper Ram (in.): 3
Width of Upper End Plates (in.): 50
Press (IPM): 40
Rapid Approach (IPM): 87
Return to Open (IPM): 115
2-Speed Electric Shift: Std.
HP: 20 HP, 208/230v, 54amps or 460v, 27 amps (specify)
Weight (lbs.): 26,000

**ESTIMATED WEIGHTS. The weight of your machine may vary from the estimated weight listed here.
Weights may vary according to options included.
> For specs on larger machines please call or email us and we will provide those for you.
> All dimensions are in inches unless otherwise noted. (To convert to centimeters multiply by 2.54)
> Engineering data and dimensions are subject to change without notice due to continuing product development.
> Foundation plans are available upon request.
> Die Blocks are not furnished.
> To convert Horsepower to KW, multiply by 0.746

Specifications are subject to change without notice.
NOTE: Data is provided by the manufacturer.
WARRANTY: 1 YEAR – Parts

OPTIONAL ITEMS:

• Factory Start Up by Base Service Technician …… $1,250.00 per day plus expenses
• *24″ Support Arms “Slide” Type W/T-Slots …………………… $1,200.00 pair
• *Keylock Switch ……………………………………………………………. $300.00
• *Light Curtain ……………………………………………………………….. $7,500.00
• Manual Front Reading Backgauge (24”) with Mechanical Readout …. $CALL
• *One Shot Lubrication …………………………………………………. $1,100.00
• *Operator Station Palm Control …………………………………… $1,900.00
• *Variable Tonnage Control ………………………………………….. $1,550.00
• *Work Light ………………………………………………………………….. $450.00
• 208v Single Phase …………………………. $CALL
• Additional Foot Pedal with Keylock ……………………………… $CALL
• Air Lift (Recommended for 4/Way Dies ……………………….. $CALL
• Angle Brackets (Plates) for Bottom (4″x4″) 18″ Shorter than Bed ……. $300.00 per foot
• Angle Brackets (Plates) for Top (4″x4″) 18″ Shorter than Bed ……… $300.00 per foot
• Automatic Lubrication ………………………………………………….. $3,100.00 each
• Bed Machining Angle Brackets ……………………………………. $1,900.00
• Bolt/Shim Kit for Leveling  ……………………………………….. $450.00
• CNC Backgauge ……………………………. $CALL
• CNC Ram Stop ……………………………… $CALL
• Crating Charge (Not an Export Crate) Still Requires Tarping ….. P.O.R.
• Die Riser ……………………………………………………………… P.O.R.
• Die Rollover Bars (Recommended for 4/Way Dies) ….. $250.00
• Disappearing Stops (Support Arms) ……………………….. $200.00 each
• Dove Tails …………………………………….. $CALL
• Dual Calibration …………………………… $CALL
• Extended Support Arms (each) ………………………………… $60.00 per foot
• Extra Length on Backgauge ……………………………………… $CALL
• Extra Foot Pedal w/Keylock Switch …………………………… $1,000.00
• Increase Stroke Length ……………………………………………. P.O.R.
• Increase Throat Gap or Increase Open Height
  • 50, 70, 95 Ton ………….. $1,000.00 per inch
  • 120, 160, 190 Ton ……. $1,800.00 per inch
  • 240 Ton ……………………. $2,000.00 per inch
• Micrometer Precision Gauge Unit (2 Required) ……. $CALL
• Oil Cooler (Kidney Loop System) ……………………………… $7,500.00
• Palm Buttons/Foot Control System (Hand buttons to preset height, stop and hold, foot to continue to shut height) …………………………………………$3,100.00
• Power Front Reading Backgauge with 5 Station NC “GO-TO” Positioner on Pendant … $CALL
• Power Ram Adjustment with 5 Station NC “GO-TO” Positioner on Pendant …. $CALL
• Ram Machining ………………………………….. $1,900.00
• Ram Stop Control (1/4″ above die) ………….. P.O.R.
• Special Application Tooling ………….. $CALL
• Special Paint Colors …………………….. P.O.R.
• T-Slots ………………………………………….. $300.00 per foot
• BACKGAUGES AND RAM CONTROL:
  • *Manual Front Reading Backgauge (24″) w/Mechanical Readout ….. $3,500.00
  • Power Front Reading Backgauge w/5 Station NC “Go To” Positioner on Pendant …… $5,500.00
  • Power Ram Adjustment w/5 Station NC “Go To” Positioner on Pendant ……. $2,500.00
  • Extra Length on Backgauge ……………………….. $1,000.00
  • CNC Backgauge …………………………………………. P.O.R.

Rigging, Lagging, Leveling and Electrical Hook Up is Customers Responsibility
ASK ABOUT OPTIONS NOT LISTED.
ALL PRICES SUBJECT TO CHANGE WITHOUT NOTICE.
NOTE: DIE RISERS NOT FURNISHED
*RECOMMENDED OPTIONS

The post BETENBENDER 14ft x 120 Ton Hydraulic Press Brake | Model 14-120 appeared first on Sheet Metal Machines.

• MADE IN USA
• Frame: The frame is of open throat design with mounting holes in feet. Drilled and tapped holes in feet allow for leveling of the machine.
• Bed: The machined flat surface is slotted full length to accommodate standard die holders, filter blocks, misc.
• Front & Back of Bed: The bed is machined down 4” on the front and 12” on the back to allow a flat surface for mounting various brackets, supports and gauges.
• Ram: The ram is constructed of solid steel slotted to accept standard dies. The clamping bar is sectional for positive clamping. The upper is machined up to 4” to allow a flat surface for mounting brackets and gauges.
• Ram Tilt Adjustment: The micrometer spindle is located on the right side end frame of machine, which allows for adjustment of the desired angle required up to ±0.500 inch. The micrometer allows the operator to return to a given setting, parallel to desired angle. By using the micrometer reading, the machine can return to previous position.
• Ram Level: The ram level is accomplished by two hydraulic systems, one for each cylinder, which keeps them parallel. The ram self-levels at the bottom of each stroke even if hydraulic system is out of adjustment.
• Hydraulic Cylinders: Direct acting hydraulic cylinders are one piece, double acting with self-aligning, hardened ball sockets.
• Accuracy: Parallelism is maintained at ±0.002 inch in low speed.
• Operating Controls:
  • 1. Pull to start. Push off. Light is on when in the “ON” position.
  • 2. Run/Jog switch. Run position for normal operation. Jog position for loading of tooling, maintenance and set-up.
    Up/Down buttons are used when in jog.
  • 3. 3 Position Foot Petal
    a. Ram up
    b. Ram hold
    c. Foot petal down. Ram down allows or jogging of ram down and holding. Emergency stop and emergency up buttons are located on a small pedestal that comes from the foot petal.
  • 4. Cycle time delay at bottom of stroke
• *When using top & bottom tools on a press brake, a forming system is created which requires analysis to determine the appropriate safeguarding for operator safety and protection.
• *It is the user’s responsibility to ensure that the point of operation is effective and all applicable safety requirements are met.
• Stroke Control (Optional): Control of strokes in accomplished by rotation of hand wheels, which read in thousandths of an inch and set the closed height. When the machine is 2 or 3 speed, the knob for setting the speed change point is located on right side for simple adjustments.
• Tonnage Control (Optional): Our machines are equipped with optional adjustable
  tonnage control to go from lower tonnage to rated tonnage of machine, as well as overload protection.
• Backgauge: A slide and clamp, 3 axis backgauge 24” is standard.
  • 1. Front operated manual backgauge, hand wheel with mechanical readout (0.01)
  • 2. Front operated power backgauge with LED readout (0.001)
    CNC backgauging and front gauging is optional.
• Front Support Arms (Optional): 24” support arms are “slide” type. Optional disappearing stops help to hold the material from sliding backward.
• Electrical System: The electrical systems meet NFPA 79 standards. All machines have
  disconnect switches, magnetic starters, 110/120v controls, 208-230/460v 3 phase, others optional.
• Motors: Our American made motors are rated for continuous duty, open drip.
• Lubrication: Grease zerks are standard. One shot lube or automatic lubrication is optional.
• Safety Features: Betenbender Hydraulic Press Brakes and Shears are built to meet ANSI B11.3 standards. Safety features of the Betenbender Press Brake include:
  • Emergency stop on pedestal
  • Emergency up on pedestal
  • Warning signs, safety markings and covers
  • Electronics meet NFPA 79 standards
  • 110/120v control
• Specifications are subject to change withoutnotice.
• Compliance with OSHA requirements is the legal responsibility of the user and is subject to local inspectors’ interpretation of existing standards.
• Betenbender Shears are built to meet ANSI B11.3 standards

STANDARD EQUIPMENT:

• Clamp Type Backgauge-Manual Adjustment X, Y, and Z
• Two Speed Ram
• Bottom Time Delay
• Three Position Foot Pedal
• Depth Stop w/Digital Readout
• Three Speed (95T and Larger)
• American Made Motors
• Hour Meter
• Nema Electrics
• All Hydraulic Fluids Included
• Disconnect Switch
• All Steel Construction
• NOTE: DIE RISERS NOT FURNISHED

SPECIFICATIONS:
Overall Width (in.): 56-1/2
Width of Bed (in.): 4
Width of Upper Machined Ram (in.): 2-1/4
Overall Height (in.): 103
Throat Depth (in.): 8
Open Height (in.): 14
Closed Height (in.): 6
Height of Bed (in.): 37
Overall Length (in.): 207
Distance Between Housing (in.): 174-1/2
Width of Upper Ram (in.): 2-1/2
Width of Upper End Plates (in.): 50
Press (IPM): 50
Rapid Approach (IPM): 114
Return to Open (IPM): 168
2-Speed Electric Shift: Std.
HP: 20 HP, 208/230v, 54amps or 460v, 27 amps (specify)
Weight (lbs.): 24,000

**ESTIMATED WEIGHTS. The weight of your machine may vary from the estimated weight listed here.
Weights may vary according to options included.
> For specs on larger machines please call or email us and we will provide those for you.
> All dimensions are in inches unless otherwise noted. (To convert to centimeters multiply by 2.54)
> Engineering data and dimensions are subject to change without notice due to continuing product development.
> Foundation plans are available upon request.
> Die Blocks are not furnished.
> To convert Horsepower to KW, multiply by 0.746

Specifications are subject to change without notice.
NOTE: Data is provided by the manufacturer.
WARRANTY: 1 YEAR – Parts

OPTIONAL ITEMS: 

• Factory Start Up by Base Service Technician …… $1,250.00 per day plus expenses
• *24″ Support Arms “Slide” Type W/T-Slots …………………… $1,200.00 pair
• *Keylock Switch ……………………………………………………………. $300.00
• *Light Curtain ……………………………………………………………….. $7,500.00
• Manual Front Reading Backgauge (24”) with Mechanical Readout …. $CALL
• *One Shot Lubrication …………………………………………………. $1,100.00
• *Operator Station Palm Control …………………………………… $1,900.00
• *Variable Tonnage Control ………………………………………….. $1,550.00
• *Work Light ………………………………………………………………….. $450.00
• 208v Single Phase …………………………. $CALL
• Additional Foot Pedal with Keylock ……………………………… $CALL
• Air Lift (Recommended for 4/Way Dies ……………………….. $CALL
• Angle Brackets (Plates) for Bottom (4″x4″) 18″ Shorter than Bed ……. $300.00 per foot
• Angle Brackets (Plates) for Top (4″x4″) 18″ Shorter than Bed ……… $300.00 per foot
• Automatic Lubrication ………………………………………………….. $3,100.00 each
• Bed Machining Angle Brackets ……………………………………. $1,900.00
• Bolt/Shim Kit for Leveling  ……………………………………….. $450.00
• CNC Backgauge ……………………………. $CALL
• CNC Ram Stop ……………………………… $CALL
• Crating Charge (Not an Export Crate) Still Requires Tarping ….. P.O.R.
• Die Riser ……………………………………………………………… P.O.R.
• Die Rollover Bars (Recommended for 4/Way Dies) ….. $250.00
• Disappearing Stops (Support Arms) ……………………….. $200.00 each
• Dove Tails …………………………………….. $CALL
• Dual Calibration …………………………… $CALL
• Extended Support Arms (each) ………………………………… $60.00 per foot
• Extra Length on Backgauge ……………………………………… $CALL
• Extra Foot Pedal w/Keylock Switch …………………………… $1,000.00
• Increase Stroke Length ……………………………………………. P.O.R.
• Increase Throat Gap or Increase Open Height
  • 50, 70, 95 Ton ………….. $1,000.00 per inch
  • 120, 160, 190 Ton ……. $1,800.00 per inch
  • 240 Ton ……………………. $2,000.00 per inch
• Micrometer Precision Gauge Unit (2 Required) ……. $CALL
• Oil Cooler (Kidney Loop System) ……………………………… $7,500.00
• Palm Buttons/Foot Control System (Hand buttons to preset height, stop and hold, foot to continue to shut height) …………………………………………$3,100.00
• Power Front Reading Backgauge with 5 Station NC “GO-TO” Positioner on Pendant … $CALL
• Power Ram Adjustment with 5 Station NC “GO-TO” Positioner on Pendant …. $CALL
• Ram Machining ………………………………….. $1,900.00
• Ram Stop Control (1/4″ above die) ………….. P.O.R.
• Special Application Tooling ………….. $CALL
• Special Paint Colors …………………….. P.O.R.
• T-Slots ………………………………………….. $300.00 per foot
• BACKGAUGES AND RAM CONTROL:
  • *Manual Front Reading Backgauge (24″) w/Mechanical Readout ….. $3,500.00
  • Power Front Reading Backgauge w/5 Station NC “Go To” Positioner on Pendant …… $5,500.00
  • Power Ram Adjustment w/5 Station NC “Go To” Positioner on Pendant ……. $2,500.00
  • Extra Length on Backgauge ……………………….. $1,000.00
  • CNC Backgauge …………………………………………. P.O.R.

Rigging, Lagging, Leveling and Electrical Hook Up is Customers Responsibility
ASK ABOUT OPTIONS NOT LISTED.
ALL PRICES SUBJECT TO CHANGE WITHOUT NOTICE.
NOTE: DIE RISERS NOT FURNISHED
*RECOMMENDED OPTIONS

The post BETENBENDER 16ft x 95 Ton Hydraulic Press Brake | Model 16-95 appeared first on Sheet Metal Machines.

• MADE IN USA
• Frame: The frame is of open throat design with mounting holes in feet. Drilled and tapped holes in feet allow for leveling of the machine.
• Bed: The machined flat surface is slotted full length to accommodate standard die holders, filter blocks, misc.
• Front & Back of Bed: The bed is machined down 4” on the front and 12” on the back to allow a flat surface for mounting various brackets, supports and gauges.
• Ram: The ram is constructed of solid steel slotted to accept standard dies. The clamping bar is sectional for positive clamping. The upper is machined up to 4” to allow a flat surface for mounting brackets and gauges.
• Ram Tilt Adjustment: The micrometer spindle is located on the right side end frame of machine, which allows for adjustment of the desired angle required up to ±0.500 inch. The micrometer allows the operator to return to a given setting, parallel to desired angle. By using the micrometer reading, the machine can return to previous position.
• Ram Level: The ram level is accomplished by two hydraulic systems, one for each cylinder, which keeps them parallel. The ram self-levels at the bottom of each stroke even if hydraulic system is out of adjustment.
• Hydraulic Cylinders: Direct acting hydraulic cylinders are one piece, double acting with self-aligning, hardened ball sockets.
• Accuracy: Parallelism is maintained at ±0.002 inch in low speed.
• Operating Controls:
  • 1. Pull to start. Push off. Light is on when in the “ON” position.
  • 2. Run/Jog switch. Run position for normal operation. Jog position for loading of tooling, maintenance and set-up.
    Up/Down buttons are used when in jog.
  • 3. 3 Position Foot Petal
    a. Ram up
    b. Ram hold
    c. Foot petal down. Ram down allows or jogging of ram down and holding. Emergency stop and emergency up buttons are located on a small pedestal that comes from the foot petal.
  • 4. Cycle time delay at bottom of stroke
• *When using top & bottom tools on a press brake, a forming system is created which requires analysis to determine the appropriate safeguarding for operator safety and protection.
• *It is the user’s responsibility to ensure that the point of operation is effective and all applicable safety requirements are met.
• Stroke Control (Optional): Control of strokes in accomplished by rotation of hand wheels, which read in thousandths of an inch and set the closed height. When the machine is 2 or 3 speed, the knob for setting the speed change point is located on right side for simple adjustments.
• Tonnage Control (Optional): Our machines are equipped with optional adjustable
  tonnage control to go from lower tonnage to rated tonnage of machine, as well as overload protection.
• Backgauge: A slide and clamp, 3 axis backgauge 24” is standard.
  • 1. Front operated manual backgauge, hand wheel with mechanical readout (0.01)
  • 2. Front operated power backgauge with LED readout (0.001)
    CNC backgauging and front gauging is optional.
• Front Support Arms (Optional): 24” support arms are “slide” type. Optional disappearing stops help to hold the material from sliding backward.
• Electrical System: The electrical systems meet NFPA 79 standards. All machines have
  disconnect switches, magnetic starters, 110/120v controls, 208-230/460v 3 phase, others optional.
• Motors: Our American made motors are rated for continuous duty, open drip.
• Lubrication: Grease zerks are standard. One shot lube or automatic lubrication is optional.
• Safety Features: Betenbender Hydraulic Press Brakes and Shears are built to meet ANSI B11.3 standards. Safety features of the Betenbender Press Brake include:
  • Emergency stop on pedestal
  • Emergency up on pedestal
  • Warning signs, safety markings and covers
  • Electronics meet NFPA 79 standards
  • 110/120v control
• Specifications are subject to change withoutnotice.
• Compliance with OSHA requirements is the legal responsibility of the user and is subject to local inspectors’ interpretation of existing standards.
• Betenbender Shears are built to meet ANSI B11.3 standards

STANDARD EQUIPMENT:

• Clamp Type Backgauge-Manual Adjustment X, Y, and Z
• Two Speed Ram
• Bottom Time Delay
• Three Position Foot Pedal
• Depth Stop w/Digital Readout
• Three Speed (95T and Larger)
• American Made Motors
• Hour Meter
• Nema Electrics
• All Hydraulic Fluids Included
• Disconnect Switch
• All Steel Construction
• NOTE: DIE RISERS NOT FURNISHED

SPECIFICATIONS:
Overall Width (in.): 56-1/2
Width of Bed (in.): 4
Width of Upper Machined Ram (in.): 2-1/4
Overall Height (in.): 103
Throat Depth (in.): 8
Open Height (in.): 14
Closed Height (in.): 6
Height of Bed (in.): 37
Overall Length (in.): 183
Distance Between Housing (in.): 150-1/2
Width of Upper Ram (in.): 2-1/2
Width of Upper End Plates (in.): 50
Press (IPM): 50
Rapid Approach (IPM): 114
Return to Open (IPM): 168
2-Speed Electric Shift: Std.
HP: 20 HP, 208/230v 54amps or 460v 24amps (specify)
Weight (lbs.): 23,000

**ESTIMATED WEIGHTS. The weight of your machine may vary from the estimated weight listed here.
Weights may vary according to options included.
> For specs on larger machines please call or email us and we will provide those for you.
> All dimensions are in inches unless otherwise noted. (To convert to centimeters multiply by 2.54)
> Engineering data and dimensions are subject to change without notice due to continuing product development.
> Foundation plans are available upon request.
> Die Blocks are not furnished.
> To convert Horsepower to KW, multiply by 0.746

Specifications are subject to change without notice.
NOTE: Data is provided by the manufacturer.
WARRANTY: 1 YEAR – Parts

OPTIONAL ITEMS: 

• Factory Start Up by Base Service Technician …… $1,250.00 per day plus expenses
• *24″ Support Arms “Slide” Type W/T-Slots …………………… $1,200.00 pair
• *Keylock Switch ……………………………………………………………. $300.00
• *Light Curtain ……………………………………………………………….. $7,500.00
• Manual Front Reading Backgauge (24”) with Mechanical Readout …. $CALL
• *One Shot Lubrication …………………………………………………. $1,100.00
• *Operator Station Palm Control …………………………………… $1,900.00
• *Variable Tonnage Control ………………………………………….. $1,550.00
• *Work Light ………………………………………………………………….. $450.00
• 208v Single Phase …………………………. $CALL
• Additional Foot Pedal with Keylock ……………………………… $CALL
• Air Lift (Recommended for 4/Way Dies ……………………….. $CALL
• Angle Brackets (Plates) for Bottom (4″x4″) 18″ Shorter than Bed ……. $300.00 per foot
• Angle Brackets (Plates) for Top (4″x4″) 18″ Shorter than Bed ……… $300.00 per foot
• Automatic Lubrication ………………………………………………….. $3,100.00 each
• Bed Machining Angle Brackets ……………………………………. $1,900.00
• Bolt/Shim Kit for Leveling  ……………………………………….. $450.00
• CNC Backgauge ……………………………. $CALL
• CNC Ram Stop ……………………………… $CALL
• Crating Charge (Not an Export Crate) Still Requires Tarping ….. P.O.R.
• Die Riser ……………………………………………………………… P.O.R.
• Die Rollover Bars (Recommended for 4/Way Dies) ….. $250.00
• Disappearing Stops (Support Arms) ……………………….. $200.00 each
• Dove Tails …………………………………….. $CALL
• Dual Calibration …………………………… $CALL
• Extended Support Arms (each) ………………………………… $60.00 per foot
• Extra Length on Backgauge ……………………………………… $CALL
• Extra Foot Pedal w/Keylock Switch …………………………… $1,000.00
• Increase Stroke Length ……………………………………………. P.O.R.
• Increase Throat Gap or Increase Open Height
  • 50, 70, 95 Ton ………….. $1,000.00 per inch
  • 120, 160, 190 Ton ……. $1,800.00 per inch
  • 240 Ton ……………………. $2,000.00 per inch
• Micrometer Precision Gauge Unit (2 Required) ……. $CALL
• Oil Cooler (Kidney Loop System) ……………………………… $7,500.00
• Palm Buttons/Foot Control System (Hand buttons to preset height, stop and hold, foot to continue to shut height) …………………………………………$3,100.00
• Power Front Reading Backgauge with 5 Station NC “GO-TO” Positioner on Pendant … $CALL
• Power Ram Adjustment with 5 Station NC “GO-TO” Positioner on Pendant …. $CALL
• Ram Machining ………………………………….. $1,900.00
• Ram Stop Control (1/4″ above die) ………….. P.O.R.
• Special Application Tooling ………….. $CALL
• Special Paint Colors …………………….. P.O.R.
• T-Slots ………………………………………….. $300.00 per foot
• BACKGAUGES AND RAM CONTROL:
  • *Manual Front Reading Backgauge (24″) w/Mechanical Readout ….. $3,500.00
  • Power Front Reading Backgauge w/5 Station NC “Go To” Positioner on Pendant …… $5,500.00
  • Power Ram Adjustment w/5 Station NC “Go To” Positioner on Pendant ……. $2,500.00
  • Extra Length on Backgauge ……………………….. $1,000.00
  • CNC Backgauge …………………………………………. P.O.R.

Rigging, Lagging, Leveling and Electrical Hook Up is Customers Responsibility
ASK ABOUT OPTIONS NOT LISTED.
ALL PRICES SUBJECT TO CHANGE WITHOUT NOTICE.
NOTE: DIE RISERS NOT FURNISHED
*RECOMMENDED OPTIONS

The post BETENBENDER 14ft x 95 Ton Hydraulic Press Brake | Model 14-95 appeared first on Sheet Metal Machines.

• MADE IN USA
• Frame: The frame is of open throat design with mounting holes in feet. Drilled and tapped holes in feet allow for leveling of the machine.
• Bed: The machined flat surface is slotted full length to accommodate standard die holders, filter blocks, misc.
• Front & Back of Bed: The bed is machined down 4” on the front and 12” on the back to allow a flat surface for mounting various brackets, supports and gauges.
• Ram: The ram is constructed of solid steel slotted to accept standard dies. The clamping bar is sectional for positive clamping. The upper is machined up to 4” to allow a flat surface for mounting brackets and gauges.
• Ram Tilt Adjustment: The micrometer spindle is located on the right side end frame of machine, which allows for adjustment of the desired angle required up to ±0.500 inch. The micrometer allows the operator to return to a given setting, parallel to desired angle. By using the micrometer reading, the machine can return to previous position.
• Ram Level: The ram level is accomplished by two hydraulic systems, one for each cylinder, which keeps them parallel. The ram self-levels at the bottom of each stroke even if hydraulic system is out of adjustment.
• Hydraulic Cylinders: Direct acting hydraulic cylinders are one piece, double acting with self-aligning, hardened ball sockets.
• Accuracy: Parallelism is maintained at ±0.002 inch in low speed.
• Operating Controls:
  • 1. Pull to start. Push off. Light is on when in the “ON” position.
  • 2. Run/Jog switch. Run position for normal operation. Jog position for loading of tooling, maintenance and set-up.
    Up/Down buttons are used when in jog.
  • 3. 3 Position Foot Petal
    a. Ram up
    b. Ram hold
    c. Foot petal down. Ram down allows or jogging of ram down and holding. Emergency stop and emergency up buttons are located on a small pedestal that comes from the foot petal.
  • 4. Cycle time delay at bottom of stroke
• *When using top & bottom tools on a press brake, a forming system is created which requires analysis to determine the appropriate safeguarding for operator safety and protection.
• *It is the user’s responsibility to ensure that the point of operation is effective and all applicable safety requirements are met.
• Stroke Control (Optional): Control of strokes in accomplished by rotation of hand wheels, which read in thousandths of an inch and set the closed height. When the machine is 2 or 3 speed, the knob for setting the speed change point is located on right side for simple adjustments.
• Tonnage Control (Optional): Our machines are equipped with optional adjustable
  tonnage control to go from lower tonnage to rated tonnage of machine, as well as overload protection.
• Backgauge: A slide and clamp, 3 axis backgauge 24” is standard.
  • 1. Front operated manual backgauge, hand wheel with mechanical readout (0.01)
  • 2. Front operated power backgauge with LED readout (0.001)
    CNC backgauging and front gauging is optional.
• Front Support Arms (Optional): 24” support arms are “slide” type. Optional disappearing stops help to hold the material from sliding backward.
• Electrical System: The electrical systems meet NFPA 79 standards. All machines have
  disconnect switches, magnetic starters, 110/120v controls, 208-230/460v 3 phase, others optional.
• Motors: Our American made motors are rated for continuous duty, open drip.
• Lubrication: Grease zerks are standard. One shot lube or automatic lubrication is optional.
• Safety Features: Betenbender Hydraulic Press Brakes and Shears are built to meet ANSI B11.3 standards. Safety features of the Betenbender Press Brake include:
  • Emergency stop on pedestal
  • Emergency up on pedestal
  • Warning signs, safety markings and covers
  • Electronics meet NFPA 79 standards
  • 110/120v control
• Specifications are subject to change without notice.
• Compliance with OSHA requirements is the legal responsibility of the user and is subject to local inspectors’ interpretation of existing standards.
• Betenbender Shears are built to meet ANSI B11.3 standards

STANDARD EQUIPMENT:

• Clamp Type Backgauge-Manual Adjustment X, Y, and Z
• Two Speed Ram
• Bottom Time Delay
• Three Position Foot Pedal
• Depth Stop w/Digital Readout
• Three Speed (95T and Larger)
• American Made Motors
• Hour Meter
• Nema Electrics
• All Hydraulic Fluids Included
• Disconnect Switch
• All Steel Construction
• NOTE: DIE RISERS NOT FURNISHED

SPECIFICATIONS:
Overall Width (in.): 45
Width of Bed (in.): 4
Width of Upper Machined Ram (in.): 1-3/4
Overall Height (in.): 96
Throat Depth (in.): 8
Open Height (in.): 14
Closed Height (in.): 6
Height of Bed (in.): 28
Overall Length (in.): 183
Distance Between Housing (in.): 150-1/2
Width of Upper Ram (in.): 2
Width of Upper End Plates (in.): 36
Press (IPM): 0-44
Rapid Approach (IPM): 44
Return to Open (IPM): 63
2-Speed Electric Shift: Std.
HP: 10 HP, 208/230v 28amps or 460v 14 amps (specify)
Weight (lbs.): 15,500

**ESTIMATED WEIGHTS. The weight of your machine may vary from the estimated weight listed here.
Weights may vary according to options included.
> For specs on larger machines please call or email us and we will provide those for you.
> All dimensions are in inches unless otherwise noted. (To convert to centimeters multiply by 2.54)
> Engineering data and dimensions are subject to change without notice due to continuing product development.
> Foundation plans are available upon request.
> Die Blocks are not furnished.
> To convert Horsepower to KW, multiply by 0.746

Specifications are subject to change without notice.
NOTE: Data is provided by the manufacturer.
WARRANTY: 1 YEAR – Parts

OPTIONAL ITEMS:

• Factory Start Up by Base Service Technician …… $1,250.00 per day plus expenses
• *24″ Support Arms “Slide” Type W/T-Slots …………………… $1,200.00 pair
• *Keylock Switch ……………………………………………………………. $300.00
• *Light Curtain ……………………………………………………………….. $7,500.00
• Manual Front Reading Backgauge (24”) with Mechanical Readout …. $CALL
• *One Shot Lubrication …………………………………………………. $1,100.00
• *Operator Station Palm Control …………………………………… $1,900.00
• *Variable Tonnage Control ………………………………………….. $1,550.00
• *Work Light ………………………………………………………………….. $450.00
• 208v Single Phase …………………………. $CALL
• Additional Foot Pedal with Keylock ……………………………… $CALL
• Air Lift (Recommended for 4/Way Dies ……………………….. $CALL
• Angle Brackets (Plates) for Bottom (4″x4″) 18″ Shorter than Bed ……. $300.00 per foot
• Angle Brackets (Plates) for Top (4″x4″) 18″ Shorter than Bed ……… $300.00 per foot
• Automatic Lubrication ………………………………………………….. $3,100.00 each
• Bed Machining Angle Brackets ……………………………………. $1,900.00
• Bolt/Shim Kit for Leveling  ……………………………………….. $450.00
• CNC Backgauge ……………………………. $CALL
• CNC Ram Stop ……………………………… $CALL
• Crating Charge (Not an Export Crate) Still Requires Tarping ….. P.O.R.
• Die Riser ……………………………………………………………… P.O.R.
• Die Rollover Bars (Recommended for 4/Way Dies) ….. $250.00
• Disappearing Stops (Support Arms) ……………………….. $200.00 each
• Dove Tails …………………………………….. $CALL
• Dual Calibration …………………………… $CALL
• Extended Support Arms (each) ………………………………… $60.00 per foot
• Extra Length on Backgauge ……………………………………… $CALL
• Extra Foot Pedal w/Keylock Switch …………………………… $1,000.00
• Increase Stroke Length ……………………………………………. P.O.R.
• Increase Throat Gap or Increase Open Height
  • 50, 70, 95 Ton ………….. $1,000.00 per inch
  • 120, 160, 190 Ton ……. $1,800.00 per inch
  • 240 Ton ……………………. $2,000.00 per inch
• Micrometer Precision Gauge Unit (2 Required) ……. $CALL
• Oil Cooler (Kidney Loop System) ……………………………… $7,500.00
• Palm Buttons/Foot Control System (Hand buttons to preset height, stop and hold, foot to continue to shut height) …………………………………………$3,100.00
• Power Front Reading Backgauge with 5 Station NC “GO-TO” Positioner on Pendant … $CALL
• Power Ram Adjustment with 5 Station NC “GO-TO” Positioner on Pendant …. $CALL
• Ram Machining ………………………………….. $1,900.00
• Ram Stop Control (1/4″ above die) ………….. P.O.R.
• Special Application Tooling ………….. $CALL
• Special Paint Colors …………………….. P.O.R.
• T-Slots ………………………………………….. $300.00 per foot
• BACKGAUGES AND RAM CONTROL:
  • *Manual Front Reading Backgauge (24″) w/Mechanical Readout ….. $3,500.00
  • Power Front Reading Backgauge w/5 Station NC “Go To” Positioner on Pendant …… $5,500.00
  • Power Ram Adjustment w/5 Station NC “Go To” Positioner on Pendant ……. $2,500.00
  • Extra Length on Backgauge ……………………….. $1,000.00
  • CNC Backgauge …………………………………………. P.O.R.

Rigging, Lagging, Leveling and Electrical Hook Up is Customers Responsibility
ASK ABOUT OPTIONS NOT LISTED.
ALL PRICES SUBJECT TO CHANGE WITHOUT NOTICE.
NOTE: DIE RISERS NOT FURNISHED
*RECOMMENDED OPTIONS

The post BETENBENDER 14ft x 70 Ton Hydraulic Press Brake | Model 14-70 appeared first on Sheet Metal Machines.

• MADE IN USA
• Frame and Base: Side frames are welded to the table base assembly as a closed end type, which is standard. With the gap end option, base of end housings have provisions to anchor machines to flat surface. The upper knife is manufactured with means of adjustment for obtaining and maintaining clearance adjustment between upper and lower knives. Mounting holes in the feet allow for firm attachment to the floor and leveling of the machine.
• Table: The table is constructed of fabricated steel, which is flat to ±0.005 inch per linear foot. The standard table is solid for the first 24 inches on the right side with support beams 16 inches on center for balance of machine.
• Options:
  1. Solid table top bolt on segments
  2. Machined bed
  3. Hand slots (optional where specified)
  4. Ball transfers (available in any of the table top patterns – open, bolt on segments or machined solid table top)
• Ram: The ram is guided through the shearing stroke by a bronze slide assembly and a steel assembly. The assemblies guide the ram on a vertical shearing plane with 2 angular degrees off the shearing plane of the stationary knife. The bronze slides have a large surface area to dissipate pressure per square inch. The PSI is low in comparison to machines that use swings or have many pins and little area to dissipate the pressure. Optional non-metalic slide assemblies are available to replace bronze.
• Hydraulic System: The hydraulic system is designed for the capacity of the rated machine to JIC standards. The hydraulic system has safety overload protection. Hoses, tubes and fittings are rated at no less than 150% of the rated working pressure.
• Hydraulic Cylinder Drive: There are two direct acting hydraulic cylinders for directing
  the ram. The hydraulic cylinder drive has double acting pistons and ball sockets for self-aligning joints.
• Hydraulic Hold down System: On the 1/8” (10 GA), 3/16” and 1/4” machines the hydraulic self-compensating spring plunger bar assembly has plungers every 4 inches for the first 24 inches and plungers 8 inches on center for the remainder of the bar. On 3/8”, 1/2”, 5/8”, 3/4”, and 1” machines, the plungers are spread every 5 inches for the first 24 inches and plungers 8½ inches on center for the remainder of the bar. The
  hydraulic holddown system automatically secures the workpiece during ram down-stroke and releases on return stroke. Optional independent holddown control is available. Refer to chart for the number of plungers.
• Reservoir: The reservoir features combination level and temperature gauges and a cleanable filter system capable of removing particles 10 microns in size.
• Shear Knife: Our knives are made of a shock resistant grade of modified high carbon, high chrome with four edges. Harder grade of high carbon, high chrome is available.
• Controls: Controls include:
  1. Pull to start, push to stop.
  2. Jog (inch)- Single stroke – run
  Optional: Continuous stroke
  3. Single palm button for stroke
  4. Backgauge controls:
  • forward/reverse
  • variable speed

  5. Emergency up-switch

• Rake Angle and Rake Angle Adjustment: Power rake angle adjustment is standard. Angle is maintained throughout cutting cycle, when rake angle is adjusted to require angle. Refer to chart.
  Increased adjustable rake angle is standard on all machines to allow for cutting of harder and heavier material.
• Electrical System: The electrical systems meets NFPA 79 standards. All machines have disconnect switches, magnetic starters, 110/120v controls, 208-230/460v 3 phase, others optional.
• Motors: Motors are open drip with sealed and permanent lubricated bearings.
• Control Circuit Voltage: Control voltage is 110/120v supplied by a transformer.
• Backgauge: 36” power operated backgauge is standard. Controls are located on front of the machine. 5 Station NC “GO-TO” Positioner is standard.
• Front Support Arms (Optional): Front support arms are available with or without scales.
• Squaring Gauge: 4’ squaring arm on right-hand side with scale is standard. Left-hand squaring arm and longer gauges are optional.
• Angle Gauge (Optional): Angle gauge marked in 1/2° increments.
• Light Beam Gauge (Standard): Shearing gauge utilizes light beam shadow as the shearing line.
• Capacity: Machines are based on 80,000 pounds tensile. Other options are available upon request.
• Shearing Accuracy: The Betenbender Hydraulic Shears will meet or exceed shearing accuracy of material ranging up to the full width capacity of the machine to precision tolerances. The width of the sheared workpiece shall be within ±0.005 inch of the backguage settings.
• Safety Features: The Betenbender Hydraulic
  Shears are built to meet ANSI B11.4 standards.
  Some of the safety features of the Betenbender
  Shears are:
  • Finger Guard for holddown w/ safety switch
  • 110/120v control
  • Guarded foot petal
  • Warning signs, safety markings & covers
  • Electronics meet NFPA 79 standards
  • Central systems provide the operator with complete control to stop & reverse the ram by simply releasing the control
  • For multiple operators, a separate control for each person, can be provided within reach of the machine
  • Emergency up-switch on control panel
• Specifications are subject to change without notice.
• Compliance with OSHA requirements is the legal responsibility of the user and is subject to local inspectors’ interpretation of existing standards.
• Betenbender Shears are built to meet ANSI B11.4 standards

STANDARD FEATURES:

• 208-230/460v 3 phase
• 36” Power Backgauge with LED Readout Inch / Metric
• 4’ Squaring Arm with Inlaid Scale
• All Hydraulic Fluids Included
• All Steel Construction
• American Made Hoses and Fittings
• American Made Motor and Valves
• Disconnect Switch
• Hour Meter
• Hydraulic Pressure: 2250 psi
• Hydraulic Self-Compensating Holddown Bar Assembly
• Light Beam Gauge (Shadow Line)
• Linemaster Foot Switch
• Manual Rapid Blade Gap Adjustment (3/8” and Larger)
• Manual Swingup Backgauge
• NEMA Electrics
• Power Adjust Variable Rake
• Safety Switch for Front Guard
• Single Piece Top and Bottom, Shock Resistant Knives with Four Cutting Edges

SPECIFICATIONS:
Knives (in.): 1×4
H.P.*: 20 HP, 208/230v, 52amps or 460v, 26amps (specify)
A – Overall Length (in.): 195-1/2
B – Overall Height (in.): 84
C – Table Height (in.): 32
D – Anchor Bolt Dimension/Length (in.): 176
E – Anchor Bolt Dimension/Width (in.): 55
F – End Plate Width (in.): 48
G – Machine w/ Backgauge (in.): 80
H – Squaring Arm Length (4’ Std.) (in.): 24
I – Knife Length (in.): 172
J – Rake Angle per Rated Capacity (in.): 3/8
K – Strokes Per Minute: 9
L – Number of Holddown Pins: 23
Weight** (lbs.): 27,000

> Please Note: ALL measurements and weights may vary from the figures given in this Specification Chart.
> All dimensions are in inches unless otherwise noted. (To convert to centimeters multiply by 2.54)
> Engineering data and dimensions are subject to change without notice due to continuing product development.
> Foundation plans are available upon request.
> 10 GA, 3/16”, and 1/4″, machines will be low profile, unless it is a gap type machine.
*Larger motor sizes are available. To convert from horsepower to KW, multiply by 0.746
**ESTIMATED WEIGHTS. The weight of your machine may vary from the estimated weight listed here. Weights may vary according to options included.
***1 x 12” has separate power unit.

> Please Note: ALL measurements and weights may vary from the figures given in this Specification Chart.
> All dimensions are in inches unless otherwise noted. (To convert to centimeters multiply by 2.54)
> Engineering data and dimensions are subject to change without notice due to continuing product development.
> Foundation plans are available upon request.
> 10 GA, 3/16”, and 1/4″, machines will be low profile, unless it is a gap type machine.
*Larger motor sizes are available. To convert from horsepower to KW, multiply by 0.746
**ESTIMATED WEIGHTS. The weight of your machine may vary from the estimated weight listed here. Weights may vary according to options included.
***1 x 12” has separate power unit.

Specifications are subject to change without notice.
NOTE: Data is provided by the manufacturer.
WARRANTY: 1 YEAR – Parts

OPTIONAL ITEMS:

• Factory Start Up by Base Service Technician………………… $1,250 per day plus expenses
• 5 Station NC “GO-TO” Backgauge Positioner ………………………. $1,250.00
• *48” Support Arms/Front Gauges w/T-Slots ……………………….. $975.00 pair
• Inlaid Scale (0-48”) …………………………………………………………… $75.00 pair
• Disappearing Stops (Support Arms) …………………………………… $200.00 each
• *Solid Table Top – Bolt on Segments ………………………………….. $1,200.00
• Machined Solid Table Top Bed …………………………………………… $3,500.00
• *Neoprene Holddown Caps ………………………………………………. $13.00 each
• *One Shot Lubrication ……………………………………………………… $1,100.00
• Automatic Lubrication …………………………………………………….. $3,500.00
• Oil Cooler ……………………………………………………………………….. $1,900.00
• Ball Transfers ………………………………………………………………….. $250.00
• Angle Gauge ……………………………………………………………………. $600.00
• Electronic Stroke Control …………………………………………………. $1,000.00
• Continuous Stroke (Includes Stroke Counter) ……………………. $2,900.00
• Stroke Counter ……………………………………………………………….. $450.00
• Independent Holddown Control ………………………………………. $1,000.00
• Extra Foot Pedal with Keylock Switch ……………………………….. $1,000.00
• Extended Squaring Arm (4’ Standard) ……………………………….. $300.00 per foot
• Flip Up Stops (Squaring Arm) …………………………………………… $250.00 each
• Left Hand Squaring Arm (4’) …………………………………………….. $1,040.00
• Operator Station Palm Control …………………………………………. $1,900.00
• Light Curtain …………………………………………………………………… P.O.R.
• Increased HP (Increased Stroke) ………………………………………. P.O.R.
• Dovetail Slots or T-Slots …………………………………………………… $CALL
• Keylock Switch ……………………………………………………………….. $260.00
• Power Bade Gap Adjustment 1/4″ …………………………………….. $5,000.00
• 2 Position Power Blade Gap Adjustment (3/8” and Larger) …. $3,200.00
• **3 Position Power Blade Gap Adjustment (3/8” and Larger) .. $5,000.00
• Pneumatic Sheet Support ……………………………………………….. $CALL
• 208v Single Phase …………………………………………………………… $CALL
• Special Paint Colors …………………………………………………………. P.O.R.
• Other Electrics and Motors ……………………………………………….. P.O.R.
• Bolt/Shim Kit for Leveling ……………………………………………….. $450.00
• Crating Charge (Not an Export Crate) Still Requires Tarping … P.O.R.
• Harder Grade of High Carbon, High Chrome Knives ……. $CALL
• CSA ………………………………………………………………………… $CALL
• Phenolic Tabletop …………………………………………………… $CALL
• BACKGAUGES:
  • Manual Swing Up Backgauge (Standard)……….. P.O.R.
  • **Automatic Power Lift Backgauge ………………. $3,500.00
  • Extra Length on Backgauge …………………………. $1,600.00 per foot
  • CNC Frontgauge …………………………………………. $ P.O.R.

Rigging, Lagging, Leveling and Electrical Hook Up is Customers Responsibility
ASK ABOUT OPTIONS NOT LISTED.
ALL PRICES ARE SUBJECT TO CHANGE WITHOUT NOTICE.
* RECOMMENDED OPTIONS FOR ALL MACHINES.
** RECOMMENDED OPTIONS FOR 3/8″, 1/2″, 5/8″  AND 3/4″ MACHINES.

The post BETENBENDER 14ft x 3/8 in. Hydraulic Shear | Model 14-375 appeared first on Sheet Metal Machines.

• MADE IN USA
• Frame and Base: Side frames are welded to the table base assembly as a closed end type, which is standard. With the gap end option, base of end housings have provisions to anchor machines to flat surface. The upper knife is manufactured with means of adjustment for obtaining and maintaining clearance adjustment between upper and lower knives. Mounting holes in the feet allow for firm attachment to the floor and leveling of the machine.
• Table: The table is constructed of fabricated steel, which is flat to ±0.005 inch per linear foot. The standard table is solid for the first 24 inches on the right side with support beams 16 inches on center for balance of machine.
• Options:
  1. Solid table top bolt on segments
  2. Machined bed
  3. Hand slots (optional where specified)
  4. Ball transfers (available in any of the table top patterns – open, bolt on segments or machined solid table top)
• Ram: The ram is guided through the shearing stroke by a bronze slide assembly and a steel assembly. The assemblies guide the ram on a vertical shearing plane with 2 angular degrees off the shearing plane of the stationary knife. The bronze slides have a large surface area to dissipate pressure per square inch. The PSI is low in comparison to machines that use swings or have many pins and little area to dissipate the pressure. Optional non-metalic slide assemblies are available to replace bronze.
• Hydraulic System: The hydraulic system is designed for the capacity of the rated machine to JIC standards. The hydraulic system has safety overload protection. Hoses, tubes and fittings are rated at no less than 150% of the rated working pressure.
• Hydraulic Cylinder Drive: There are two direct acting hydraulic cylinders for directing
  the ram. The hydraulic cylinder drive has double acting pistons and ball sockets for self-aligning joints.
• Hydraulic Hold down System: On the 1/8” (10 GA), 3/16” and 1/4” machines the hydraulic self-compensating spring plunger bar assembly has plungers every 4 inches for the first 24 inches and plungers 8 inches on center for the remainder of the bar. On 3/8”, 1/2”, 5/8”, 3/4”, and 1” machines, the plungers are spread every 5 inches for the first 24 inches and plungers 8½ inches on center for the remainder of the bar. The
  hydraulic holddown system automatically secures the workpiece during ram down-stroke and releases on return stroke. Optional independent holddown control is available. Refer to chart for the number of plungers.
• Reservoir: The reservoir features combination level and temperature gauges and a cleanable filter system capable of removing particles 10 microns in size.
• Shear Knife: Our knives are made of a shock resistant grade of modified high carbon, high chrome with four edges. Harder grade of high carbon, high chrome is available.
• Controls: Controls include:
  1. Pull to start, push to stop.
  2. Jog (inch)- Single stroke – run
  Optional: Continuous stroke
  3. Single palm button for stroke
  4. Backgauge controls:
  • forward/reverse
  • variable speed

  5. Emergency up-switch

• Rake Angle and Rake Angle Adjustment: Power rake angle adjustment is standard. Angle is maintained throughout cutting cycle, when rake angle is adjusted to require angle. Refer to chart.
  Increased adjustable rake angle is standard on all machines to allow for cutting of harder and heavier material.
• Electrical System: The electrical systems meets NFPA 79 standards. All machines have disconnect switches, magnetic starters, 110/120v controls, 208-230/460v 3 phase, others optional.
• Motors: Motors are open drip with sealed and permanent lubricated bearings.
• Control Circuit Voltage: Control voltage is 110/120v supplied by a transformer.
• Backgauge: 36” power operated backgauge is standard. Controls are located on front of the machine. 5 Station NC “GO-TO” Positioner is standard.
• Front Support Arms (Optional): Front support arms are available with or without scales.
• Squaring Gauge: 4’ squaring arm on right-hand side with scale is standard. Left-hand squaring arm and longer gauges are optional.
• Angle Gauge (Optional): Angle gauge marked in 1/2° increments.
• Light Beam Gauge (Standard): Shearing gauge utilizes light beam shadow as the shearing line.
• Capacity: Machines are based on 80,000 pounds tensile. Other options are available upon request.
• Shearing Accuracy: The Betenbender Hydraulic Shears will meet or exceed shearing accuracy of material ranging up to the full width capacity of the machine to precision tolerances. The width of the sheared workpiece shall be within ±0.005 inch of the backguage settings.
• Safety Features: The Betenbender Hydraulic
  Shears are built to meet ANSI B11.4 standards.
  Some of the safety features of the Betenbender
  Shears are:
  • Finger Guard for holddown w/ safety switch
  • 110/120v control
  • Guarded foot petal
  • Warning signs, safety markings & covers
  • Electronics meet NFPA 79 standards
  • Central systems provide the operator with complete control to stop & reverse the ram by simply releasing the control
  • For multiple operators, a separate control for each person, can be provided within reach of the machine
  • Emergency up-switch on control panel
• Specifications are subject to change without notice.
• Compliance with OSHA requirements is the legal responsibility of the user and is subject to local inspectors’ interpretation of existing standards.
• Betenbender Shears are built to meet ANSI B11.4 standards

STANDARD FEATURES:

• 208-230/460v 3 phase
• 36” Power Backgauge with LED Readout Inch / Metric
• 4’ Squaring Arm with Inlaid Scale
• All Hydraulic Fluids Included
• All Steel Construction
• American Made Hoses and Fittings
• American Made Motor and Valves
• Disconnect Switch
• Hour Meter
• Hydraulic Pressure: 2250 psi
• Hydraulic Self-Compensating Holddown Bar Assembly
• Light Beam Gauge (Shadow Line)
• Linemaster Foot Switch
• Manual Rapid Blade Gap Adjustment (3/8” and Larger)
• Manual Swingup Backgauge
• NEMA Electrics
• Power Adjust Variable Rake
• Safety Switch for Front Guard
• Single Piece Top and Bottom, Shock Resistant Knives with Four Cutting Edges

SPECIFICATIONS:
Knives (in.): 1×4
H.P. *: 15 HP, 208/230v, 39.6amps OR 460v, 19.3amps (specify)
A – Overall Length (in.): 228
B – Overall Height (in.): 61
C – Table Height (in.): 32
D – Anchor Bolt Dimension/Length (in.): 199
E – Anchor Bolt Dimension/Width (in.): 50-1/2
F – End Plate Width (in.): 44
G – Machine w/ Backgauge (in.): 76
H – Squaring Arm Length (4’ Std.) (in.): 35
I – Knife Length (in.): 196
J – Rake Angle per Rated Capacity (in.): 1/4
K – Strokes Per Minute: 10
L – Number of Holddown Pins: 25
Weight** (lbs.): 22,000

> Please Note: ALL measurements and weights may vary from the figures given in this Specification Chart.
> All dimensions are in inches unless otherwise noted. (To convert to centimeters multiply by 2.54)
> Engineering data and dimensions are subject to change without notice due to continuing product development.
> Foundation plans are available upon request.
> 10 GA, 3/16”, and 1/4″, machines will be low profile, unless it is a gap type machine.
*Larger motor sizes are available. To convert from horsepower to KW, multiply by 0.746
**ESTIMATED WEIGHTS. The weight of your machine may vary from the estimated weight listed here. Weights may vary according to options included.
***1 x 12” has separate power unit.

Specifications are subject to change without notice.
NOTE: Data is provided by the manufacturer.
WARRANTY: 1 YEAR – Parts

OPTIONAL ITEMS:

• Factory Start Up by Base Service Technician………………… $1,250 per day plus expenses
• 5 Station NC “GO-TO” Backgauge Positioner ………………………. $1,250.00
• *48” Support Arms/Front Gauges w/T-Slots ……………………….. $975.00 pair
• Inlaid Scale (0-48”) …………………………………………………………… $75.00 pair
• Disappearing Stops (Support Arms) …………………………………… $200.00 each
• *Solid Table Top – Bolt on Segments ………………………………….. $1,200.00
• Machined Solid Table Top Bed …………………………………………… $3,500.00
• *Neoprene Holddown Caps ………………………………………………. $13.00 each
• *One Shot Lubrication ……………………………………………………… $1,100.00
• Automatic Lubrication …………………………………………………….. $3,500.00
• Oil Cooler ……………………………………………………………………….. $1,900.00
• Ball Transfers ………………………………………………………………….. $250.00
• Angle Gauge ……………………………………………………………………. $600.00
• Electronic Stroke Control …………………………………………………. $1,000.00
• Continuous Stroke (Includes Stroke Counter) ……………………. $2,900.00
• Stroke Counter ……………………………………………………………….. $450.00
• Independent Holddown Control ………………………………………. $1,000.00
• Extra Foot Pedal with Keylock Switch ……………………………….. $1,000.00
• Extended Squaring Arm (4’ Standard) ……………………………….. $300.00 per foot
• Flip Up Stops (Squaring Arm) …………………………………………… $250.00 each
• Left Hand Squaring Arm (4’) …………………………………………….. $1,040.00
• Operator Station Palm Control …………………………………………. $1,900.00
• Light Curtain …………………………………………………………………… P.O.R.
• Increased HP (Increased Stroke) ………………………………………. P.O.R.
• Dovetail Slots or T-Slots …………………………………………………… $CALL
• Keylock Switch ……………………………………………………………….. $260.00
• Power Bade Gap Adjustment 1/4″ …………………………………….. $5,000.00
• 2 Position Power Blade Gap Adjustment (3/8” and Larger) …. $3,200.00
• **3 Position Power Blade Gap Adjustment (3/8” and Larger) .. $5,000.00
• Pneumatic Sheet Support ……………………………………………….. $CALL
• 208v Single Phase …………………………………………………………… $CALL
• Special Paint Colors …………………………………………………………. P.O.R.
• Other Electrics and Motors ……………………………………………….. P.O.R.
• Bolt/Shim Kit for Leveling ……………………………………………….. $450.00
• Crating Charge (Not an Export Crate) Still Requires Tarping … P.O.R.
• Harder Grade of High Carbon, High Chrome Knives ……. $CALL
• CSA ………………………………………………………………………… $CALL
• Phenolic Tabletop …………………………………………………… $CALL
• BACKGAUGES:
  • Manual Swing Up Backgauge (Standard)……….. P.O.R.
  • **Automatic Power Lift Backgauge ………………. $3,500.00
  • Extra Length on Backgauge …………………………. $1,600.00 per foot
  • CNC Frontgauge …………………………………………. $ P.O.R.

Rigging, Lagging, Leveling and Electrical Hook Up is Customers Responsibility
ASK ABOUT OPTIONS NOT LISTED.
ALL PRICES ARE SUBJECT TO CHANGE WITHOUT NOTICE.
* RECOMMENDED OPTIONS FOR ALL MACHINES.
** RECOMMENDED OPTIONS FOR 3/8″, 1/2″, 5/8″  AND 3/4″ MACHINES.

The post BETENBENDER 16ft x 1/4 in. Hydraulic Shear | Model 16-250 appeared first on Sheet Metal Machines.